Gallo Tech GTStarter-2 Operation & Installation Manual - Page 14

Browse online or download pdf Operation & Installation Manual for Remote Starter Gallo Tech GTStarter-2. Gallo Tech GTStarter-2 15 pages. Keyless rfid push button start & security system

Print Page

1. Key Fob & Programming Function Set up

For Manual Transmission: Connect the YELLOW wire to a clutch peddle switch that has a neg. (-) output when the

clutch peddle is depressed. Then change Function Option #2 to Manual Transmission.

C7: GREEN – Neg (-) Disarm Output to enable security bypass devices. Connect the GREEN wire to the Neg (-)

input of a security bypass device. These devices are used in the event that the vehicle has an OEM security system

that prevents starting the vehicle without the security key. The proper security by-pass module for the specific

vehicle can be found at www.gallotech.com/support.php. Follow the instruction that came with the by-pass module.

Installing Connector C8:

C8: Shock Sensor – The shock sensor should be mounted on a rigid member of the vehicle. Typically it is best

attached to the steering column. The shock sensor should never be mounted on the outside of the vehicle where it is

not protected from exposure to moisture. Connect the 3 Pin connector to both the shock sensor and the Control

Module as shown in Figure 1.

Installing Connector C9:

C9: - HF Antenna – The HF antenna is used for the high frequency receiver that operates the remote access

functions such as remote door locking, car locating, and anti hi-jack. If mounting this antenna under the dash, the

detection range will be reduced to about 300 Feet. If needing up to 600 feet range then mount the antenna

somewhere above the dash board level. Caution should be taken as the antenna whip is metal and the installer

should insure that the whip will not interfere / short out any under-dash wiring. Connect the 3 Pin connector to the

Control Module as shown in Figure 1.

Installing Connector C10:

C10: Valet Switch – The Valet Switch should be mounted under the dash or in the glove box so that it can be

accessed from time to time to change or modify the programmable functions of GTStarter 2. Connect the 2 pin

connector to the Control Module as shown in Figure 1.

1.6 FINAL INSTALLATION

1. Recheck all electrical connections to be certain they are connected in the proper locations and check that

all connections are wrapped with a good quality electrical tape or shrink tubing.

2. Connect all 10 module connectors to the Control Module. The Control Module should be secured under

the dash using cable ties or equivalent.

3. If the vehicle is equipped with a locking steering column, it must be permanently disabled before

attempting to drive the vehicle.

4. Reconnect the battery and thoroughly test all starting functions.



If the key FOBs are not detected by the control module, then re-learn both key FOBs.

See Sec. 1.5 (A) for code learning instructions.

Test the starting function:

Automatic transmission: Press and hold the "Push Start Stop" button without pressing the brake peddle,

making certain that the vehicle will not start. The engine must only start when the brake is pressed and the

vehicle is in Park or Neutral. Check to make sure the vehicle does not start when the gear selector is in

Drive or Reverse. If the engine starts in Drive or Reverse, then the wiring connections to the Control Module

and the connections to the Park / Neutral switch must be rechecked per Figure 1.

Manual Transmission: Set the gear selector to neutral. Press and hold the "Push Start Stop" button without

pressing the clutch peddle, making certain that the vehicle will not start. The engine must only start when

the clutch peddle is pressed. If the engine starts without the clutch peddle being depressed, then the wiring

connections to the Control Module must be rechecked per Figure 1.

5. Program the module to the functions that you desire following Sec. 1.5 "Program Function Set Up" and

Table 1 "Function Option Chart".

- 3 Pin Shock Sensor Wire Harness

- 3 Pin HF Antenna wire harness

- 2 Pin Valet Switch wire harness

- 14 -

Rev. V8.2- 20212