maimin SABRE 3000 Instruction & Parts Manual - Page 3

Browse online or download pdf Instruction & Parts Manual for Cutter maimin SABRE 3000. maimin SABRE 3000 20 pages. Straight knife cutting machine with flexi-band sharpener
Also for maimin SABRE 3000: Instructions And Parts List (12 pages)

Print Page
v
2.4
TO CUT
Raise
Presserfoot 4402
above
top of
lay by
pressing
down on
Presserfoot Handle
,4'323
and
lift ingPresserfoot
Lift
.
For
Squeeze
Trigger,
pull
Handle
23308
towards
machine
Handle
4549.
Enter
lay, and lower
Presserfoot
to top of lay by
releasing
Presserfoot
Trigger. When making turns in
lay,
it
is
sometimes
advisable
to let
Presserfoot
ride freely
on
top of
lay by
pushing
down
onPresserfootHandle.
When machine
is
not
in
use,
always
lower Presserfoot
to
Baseplate.
The Presserfoot
Leg
acts
as
a
safety guard
for
the blade.
2.5
TO CHANGE
FLD(BANDS
(Figures 2 and
3)
a)
Disconnect power.
b)
Figure
2:
Push
Block
*A"
to
release
right (upper) FlexiBand
"B".
Remove
FlexiBand from
Block
and
then from
Drive
Rrlley
"Cl'
c)
Figure
3:
Slip new
FlexiBand
"B"
over
Drive Pulley
"C
"and
between
Band Plate
"D"
and
Blade
"E."
Push
Block
"A"
forward
and slide
FlexiBand
over
it.
Release
Block
*A."
d) Remove
left (lower) FlexiBand,
and
install
new
one
in
same manner.
2.6
TO CHANGE BLADE (Figure
4)
a)
Disconnect power
and
lower
Presserfoot
Leg.
b)
Lay
machine on
left
side.
c)
Press and
turn Thumbwheel
"A"
to move Blade to
its
lowest
position.
d) With
Knife Key
"B"
turn
Nut
"C"
counter
clockwise
to
unlock
blade.
e)
Raise
Presserfoot Leg
and
slide Blade
"D"
downwards
and out.
f)
Clean Inserts "E." with.slot cleaning
tool
or
bottom corner
ofblade.
g)
Slide new
Blade up
against
Knife
Locking
Bolt.
h)
Holding
lower part
of
Blade behind
edge,
push
it
firmly
up
against
Bolt
and
back
against
Inserts.
i)
Tighten
Nut
"C."
Note: IJse
only genuine
Maimin
Blades,with
"Cut-Out"
and
T-shaped
slot
in
shank
for
optimum performance
and
safe operation.
Always
tighten
Knife Locking
Boh
and
Nut
beforc
nmning
machine
to prevent
damage
to
Crosshead
A510 and Gibbs
A513.
Do not run
sharyrener
withoat
blade
in
machine
or
sharTrener
wiII
jan
2.7
TO CHANGE BEVELWIDTH ON BLADE
(Figure
5)
a)
Run
sharpener
to
lowest
position, turn
offmotor,
discon-
nect
power.
b)
Loosen Screw
"A."
c)
Insert Bevel Adjusting
Tool
"B"
into
Washer
"C"
and
rotate
Washer
to
increase
or
decrease
blade bevel
width.
Note
arrow
on washer and
edse
width indicator
on Band Plate
Carrier
(4374).
d)
Tighten
Screw
"A."
e)
Bevel
on opposite side
is
adjusted
in
same
manner.
2.8
MAINTENANCE SCHEDULE
a)
Daily:
Fill oil
cups
(A547).
Use
either
Maimin
01122109
or
quality "30 weight"
oil
(I.S.O. viscosity grade 220).
b)
Weekly:
(1)
Sharpener-run
to
lowestposition,
turn off motor, and
blow out
lint
and dust
with
compressed
air.
(2) Motor
-
run
motor,
and
point
stream of compressed
air
into
back of
motor
and
side
of
front
housing by fan
to
eject
lint
and dust.
c)
Every500hours
of operation:
(1)
Sharpener-
Remove Cap Screw
(4'367A) from
top
of
Gear
Case
(A367
)
and
squeeze
in
a
small
amount
of Grease
22174
to
coat
gears.
(2)
Motor
-
Remove
motor
cover
and,
with
compressed
air,
blow
lint
and dust
from motor
coils and
armature.
v