CORBERO FD 5140 I Instruction Booklet - Page 4

Browse online or download pdf Instruction Booklet for Refrigerator CORBERO FD 5140 I. CORBERO FD 5140 I 10 pages.

Print Page

INSTALLATION

If this appliance featuring magnetic door seals is

to replace an older appliance having a spring lock

(latch) on the door or lid, be sure to make that

spring lock unusable before you discard the old

appliance. This will prevent it from becoming a

death-trap for a child.

Location

The appliance should be installed well away from

sources of heat such as radiators, boilers, direct sun-

light etc.

Best performance is obtained with ambient tempera-

ture between +18 C and +43 C (class T); +18 C and

+38 C (class ST); +16 C and +32 C (class N); +10 C

and +32 C (class SN).

The class of your appliance is shown on its rating

plate.

For building into kitchen units follow the special

"Building-in" instructions given.

Electrical connection

Before plugging in, ensure that the voltage and fre-

quency shown on the serial number plate correspond

to your domestic power supply.

Voltage can vary by 6% of the rated voltage.

For operation with different voltages, a suitably sized

auto-transformer must be used.

The appliance must be earthed.

The power supply cable plug is provided with a con-

tact for this purpose.

If the domestic power supply socket is not earthed,

connect the appliance to a separate earth in compli-

ance with current regulations, consulting a specialist

technician.

The Manufacturer declines all responsibility if the

above safety precautions are not observed.

This appliance complies with EEC directive

number 87/308 of 2/6/87 relative to radio inter-

ference suppression.

This appliance complies with the following

E.E.C. Directives:

- 73/23 EEC of 19.2.73 (Low Voltage Directive) and

subsequent modiﬁcations;

- 89/336 EEC of 3.5.89 (Electromagnetic Compatibil-

ity Directive) and subsequent modiﬁcations.

Cleaning the interior

Before using the appliance for the ﬁrst time, wash the

interior and all internal accessories with lukewarm wa-

ter and some neutral soap so as to remove the typical

smell of a brand-new product, then dry thoroughly.

Do not use detergents or abrasive powders, as these

will damage the ﬁnish.

Changing the opening direction of the

doors

The opening direction of the doors can be changed on

these appliances.

This must be done before the appliance is built into

the kitchen unit.

Top hinge

D120

Bottom hinge

D119

Centre hinge

D121

turn the hinge upside down and ﬁt it on the other side

of the cabinet, after having removed the covers which

mask the holes provided for ﬁxing; use the covers to

mask the holes left open;

reﬁt the two doors and tighten the top and bottom

hinges.

Using a screwdriv-

er, remove the top

hinge and reﬁt it on

the other side, af-

t e r h a v i n g re -

moved the covers

w h i c h m a s k t h e

holes provided for

ﬁxing; use these

covers to mask the

holes left open.

Remove the bot-

tom hinge (A) and

reﬁt it on the left-

hand side of bot-

to m bas e o f the

c a b i n e t , w h i c h

h a s p re - d r i l l e d

holes for ﬁxing.

A f t e r h a v i n g re -

moved the top and

bottom hinges (fol-

lowing the instruc-

tions in the previ-

ous paragraphs),

re m o v e t h e t w o

d o o r s ; u n s c re w

t h e t w o s c re w s

which secure the

centre hinge to the

appliance cabinet;