HIKOKI CV 14DBL Handling Instructions Manual - Page 3

Browse online or download pdf Handling Instructions Manual for Power Tool HIKOKI CV 14DBL. HIKOKI CV 14DBL 16 pages. Cordless multi tool

Print Page

c) When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects,

that can make a connection from one terminal to

another.

Shorting the battery terminals together may cause

burns or a ﬁ re.

d) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, ﬂ ush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation or

burns.

6) Service

a) Have your power tool serviced by a qualiﬁ ed

repair person using only identical replacement

parts.

This will ensure that the safety of the power tool is

maintained.

PRECAUTION

Keep children and inﬁ rm persons away.

When not in use, tools should be stored out of reach of

children and inﬁ rm persons.

CORDLESS MULTI TOOL SAFETY

WARNINGS

1. Hold power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring.

Cutting accessory contacting a "live" wire may make

exposed metal parts of the power tool "live" and could

give the operator an electric shock.

ADDITIONAL SAFETY WARNINGS

1. Always hold the tool ﬁ rmly with one hand on housing

(Fig. 10). Do not touch the metal part.

2. Make sure that the area to be cut is absolutely free of any

hidden obstructions including electrical wiring, water, or

gas pipes. Cutting into the aforementioned may result in

electric shock or short circuit, gas leak or other hazards

that can cause serious accidents or injuries.

3. Make sure to securely hold the tool during operation.

Failure to do so can result in accidents or injuries.

4. Secure the workpiece. A workpiece clamped with

clamping devices or in a vice is held more secure than

by hand.

5. Setting up and checking the work environment. Check

if the work environment is suitable by following the

precaution.

6. Dust particles such as silica or asbestos are hazardous

to your health. When working with materials containing

these components, take appropriate dust-prooﬁ ng

measures.

7. Working with metal can cause sparks. Make sure there

are no ﬂ ammable and combustible materials in the

vicinity and that they are stored in a safe location.

8. Do not allow foreign matter to enter the hole for

connecting the rechargeable battery.

9. Never disassemble the rechargeable battery and

charger.

10. Never

short-circuit

Shortcircuiting the battery will cause a great electric

current and overheat. It results in burn or damage to the

battery.

11. Do not dispose of the battery in ﬁ re. If the battery is burnt,

it may explode.

the

rechargeable

battery.

12. Bring the battery to the shop from which it was purchased

as soon as the post-charging battery life becomes too

short for practical use. Do not dispose of the exhausted

battery.

13. Do not insert object into the air ventilation slots of the

charger. Inserting metal objects or inﬂ ammables into the

charger air ventilation slots will result in electrical shock

hazard or damaged charger.

14. After use for continuous cutting or grinding works, rest

the unit for 15 minutes or so when replacing the battery.

The temperature of the motor, switch, etc., will rise

if the work is started again immediately after battery

replacement, eventually resulting in burnout.

15. The motor may stop in the event the tool is overloaded. In

this should occur, release the tool's switch and eliminate

the cause of the overload.

16. The use of the battery in a cold condition (below 0 degree

Centigrade) can sometimes result in the weakened

tightening torque and reduced amount of work. This,

however, is a temporary phenomenon, and returns to

normal when the battery warms up.

17. Do not look directly into the light. Such actions could

result in eye injury.

18. Do not touch the application tool, its attachment area or

other metal surfaces immediately after use as they will

be hot. Doing so may result in burns or injury.

The metal is hot and can easily burn your skin.

19. Make sure that there is no one below when operating the

tool in high locations. Dropping the tool or materials may

result in accident or injury.

20. Never apply any unreasonable force to the application

tool when working. Doing so may break the application

tool or damage the motor.

21. Do not leave the tool running unattended on the ﬂ oor,

table or other locations. Doing so may result in injury.

22. When attaching application tools, be careful not to get

your ﬁ ngers or other extremities caught in the lever.

23. If the application tool seems to be loose or uneven after

attaching it to the unit, follow the instructions in Fig. 5

and re-attach the tool. Operating the unit with a loose or

uneven application tool may result in injury.

24. When switching on the tool, make sure the application

tool is not in contact with any processing materials.

Failure to do so may result in injury.

25. For cutting eﬃ ciency, switch the mode of the application

tool according to task conditions and materials to be cut.

26. After use, be sure not to place the tool near chips or

sawdust before it comes to a full stop as the tool may

suck in those particles.

27. Do not polish wood with sanding paper used for metal

polishing.

28. Do not use worn or clogged sanding paper.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with the

protection function to stop the output.

In the cases of 1 to 3 described below, when using this

product, even if you are pulling the switch, the motor may

stop. This is not the trouble but the result of protection

function.

1. When the battery power remaining runs out, the motor

stops.

In such a case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In this

case, release the switch of tool and eliminate causes of

overloading. After that, you can use it again.

3. If the battery is overheated under overload work, the

battery power may stop.

In this case, stop using the battery and let the battery

cool. After that, you can use it again.

Furthermore, please heed the following warning and caution.