Gambro Prismaflo IIS Quick User Manual - Page 2

Browse online or download pdf Quick User Manual for Medical Equipment Gambro Prismaflo IIS. Gambro Prismaflo IIS 2 pages.

Print Page

"On" or "Heating" mode

control panel

"On" or "Heating" mode: Increasing/Decreasing the Set

Temperature

The set temperature can be checked at any time by pressing the

"Set" Button.

Actions: Press the "Set" Button while the control unit is turned on

("On" mode) or started ("Heating" mode).

While the display is ﬂashing, you can select any set temperature

between 33.0°C and 43.0°C in 1°C increments by repeatedly

pressing the Button "Set'.

When the set temperature is 43.0°C, the selection starts again at

33.0°C if you press the "Set" Button one more time.

Characteristics:

•

The set temperature is displayed and ﬂashes for approximately 3

seconds (e.g. 41.0°C).

•

After the selection has been made the display will continue to

ﬂash the set temperature for approximately 3 seconds then revert

to current temperature.

•

After changing the set temperature, the audio alarm will beep

once to conﬁrm the new set temperature.

•

When the control unit is in Heating Mode, temperature regulation

is activated with the new set temperature.

•

The set temperature is retained in memory even after power is

removed.

Operating the Prismaﬂo IIS

blood warmer

1. Plug the main plug of the Prismaﬂo IIS blood warmer into a socket

(LED "Standby" turns on to show that the control unit is in "Standby"

mode).

2. Connect the heating sleeve to the Prismaﬂo IIS blood warmer

according ﬁgures below.

3. Press the Button "Standby" to switch the Prismaﬂo IIS blood

warmer to "On" mode.

4. Check the audible and visual indicators and the display: All

segments of the display and all LEDs are ﬂashing with the audio alarm

providing a single beep to conﬁrm that the control unit is working

properly. The "Start" LED ﬂashes and the temperature display shows

the actual set temperature ﬂashing for about 3 seconds, then the

current temperature of the heating sleeve is indicated.

5. Press the "Set" Button to select another set temperature if needed.

6. Press the "Start" Button twice to switch the Prismaﬂo IIS blood

warmer to Heating Mode ("Start" LED is on permanently).

For Customer Support call 800-525-2623

14143 Denver West Parkway, Suite 400

Lakewood, CO 80401

Visit us at www.gambro.com

Gambro, Prismaflex and Prismaflo II are registered trademarks of Gambro Group.

7. Follow the online instructions of the Gambro control unit. With

Prismaﬂex system, move to next step when reaching "Prepare and

Connect Solutions" screen.

8. Align the groove of the Prismaﬂo IIS heating sleeve in an upward

position, making sure the sleeve is not twisted.

9. Place the end of the Prismaﬂex Set blood return line (blue strip) to

the end of the heating sleeve approximately 4 to 6 cm from the blue

Luer Lock connector.

10. With the thumb, insert the Prismaﬂex Set blood return line into the

sleeve up to the Gambro control unit cabinet.

11. Put the heating sleeve of the Prismaﬂo IIS blood warmer into the

support hooks for the heating sleeve with a kink-free inlet of the blood

return line.

12. Continue with online instructions of the Gambro control unit until

the patient is connected.

Installation

Patient at the right side of Gambro control unit.

Installation

Patient at the left side of Gambro control unit.

If the patient is positioned at the left side of the Gambro control unit,

the heating sleeve is guided in front of the machine from the right

support of the heating sleeve to the left support and then back to the

patient (A, B).

Manufactured by

Stihler Electronic GmbH

Julius-Hoelder-Strasse 36

70597 Stuttgart

Germany

If the patient is positioned at the

right side of the Gambro control

unit then guide the heating

proﬁle sleeve directly from the

right support of the heating

proﬁle sleeve back to the patient.