DecaLED Controller 3 Mini Manual - Page 4

Browse online or download pdf Manual for Controller DecaLED Controller 3 Mini. DecaLED Controller 3 Mini 10 pages.

Print Page

Connecting the Tension Provider

Connecting the power supply

Check whether or not the source Voltage in your area matched the required voltage for the controller power sup

Note: If the source Voltage is 110V, do NOT connect a 230V power supply. This can severely damage your devi

Check whether or not the source voltage in your area matches the required voltage for the controller power

The Controller comes with a complete power cable. The device is powered by an IEC cord which fits into the po

supply. Note: If the source voltage is 110V, do NOT connect a 230V power supply. This can severely damage

adapter (1) on the backside of the device. Keep pushing the IEC until it is fixed into position in the adapter. The

Connecting the Tension Provider

your device. The DecaLED

device can be turned on by means of a power switch. An indicator shows whether the device is turned on or off.

Check whether or not the source Voltage in your area matched the required voltage for the controller power supply.

IEC cord which fits into the power adapter (1) on the backside of the device. Keep pushing the IEC until it is

The device is powered by an IEC cord which fits into the power socket on the backside of the device. Keep pushing

Note: If the source Voltage is 110V, do NOT connect a 230V power supply. This can severely damage your device.

Connecting the DecaLED RGB modules(12V) to the DecaLED Controller 2 for 12V

fixed into position in the adapter. The device can be turned on by using the power switch. An indicator shows

the IEC until it is fixed into position in the socket. The device can be turned on by means of the power switch. An

The Controller comes with a complete power cable. The device is powered by an IEC cord which fits into the power

whether the device is turned on or off.

indicator shows whether the device is turned on or off.

adapter (1) on the backside of the device. Keep pushing the IEC until it is fixed into position in the adapter. The

device can be turned on by means of a power switch. An indicator shows whether the device is turned on or off.

Connecting the DecaLED

Connecting the DecaLED RGB modules(24V) to the DecaLED Controller 3 Mini for 24V

Connecting the DecaLED RGB modules to the DecaLED Controller 1 for RGB modules

DMX in

LED REMOTE

IR EYE(Sensor)

LED REMOTE

Configuration:

Configuration

Configuration:

1. Maximum amount of connected

1. Maximum amount of connected DecaLED

1. Maximum amount of connected

A maximum of 24 channels (8x RGB channels) can be controlled separately. O

A maximum of 6 channels (2x RGB channels) can be controlled separately. O

A maximum of 6 channels (2x RGB channels) can be controlled separatelyseparately, only a maximum

A maximum of 24 channels (8x RGB channels) can be controlled separately. The maximum amount of connected

3A(1A per individual channel) is allowed on a single output and the maximum amount of the total load can not

loading capacity of 3A(1A per individual channel) is allowed on a single output and the maximum amount of

DecaLED RGB modules must not exceed 250. Please note: only 50 modules are allowed on a single output.

exceed 12A distributed over all 8 outputs.

exceed 4.5A distributed over all 2 outputs.

the total load can not exceed 4A distributed over all 2 outputs.

2. Connector configuration

The DMX configuration is depicted below. The DMX connections consist of one XLR 3 male connector (input) and

2. Connector configuration

The DMX configuration is depicted below. The DMX connections consist of one XLR 3 male connector (input) and

one XLR 3 female connector (transited output) or 3-polar terminal connector .

The DMX configuration is depicted below. The DMX connections consist of one XLR 3 male connector (input)

one XLR 3 female connector (transited output) or 3-polar terminal connector .

and one XLR 3 female connector (transited output) or 3-polar terminal connector.

The XLR 3-polar connector: 1 = GROUND

Chassis part XLR-3 male

3. Connector configuration outputs

The XLR 3-polar connector:

The output configuration is depicted below. The output connections consist of eight 5-polar terminal connectors.

The output configuration is depicted below. The output connections consist of eight 4-polar terminal connectors.

3. Connector configuration outputs - The output configuration is depicted below. The output connections

3. Connector configuration outputs

The 5-polar terminal connector:

The 4-polar terminal connector:

consist of eight 5-polar terminal connectors.

The output configuration is depicted below. The output connections consist of eight 4-polar terminal connectors.

The 4-polar terminal connector:

1 = +

2 = R

3 = G

4 = B

NOTE:

DMX signal cable

DMX signal cable: 120 ohm impedance DMX signal cable MUST be used for signal connection.

NOTE:

A 120 ohm impedance DMX signal cable MUST be used for signal connection.

DMX signal cable: 120 ohm impedance DMX signal cable MUST be used for signal connection.

Controller 3 Mini is supplied with a power cable. The device is powered by an

24V products to the DecaLED

DMX Controller

DecaLED Controller 2

(A Driver Unit)

DecaLED Controller 3 Mini

DecaLED Controller 1

for 24V

for RGB modules

IR In

(A Driver Unit)

DMX in

IR In

DMX out

DMX in

DMX out

IR EYE(Sensor)

DMX out

DecaLED RGB modules(12V)

DecaLED RGB modules(24V)

DecaLED RGB modules

2 = DATA -

3 = DATA +

Chassis part XLR-3 female

Chassis part XLR-3 male

1 = ground, 2 = data -, 3 = data +

1 = Blue

1 = +

2 = Red

2 = R

3 = Green

3 = G

1 = +

4 = White

4 = B

2 = R

5 = Yellow

3 = G

4 = B

: 120 ohm impedance DMX signal cable

Controller 3 Mini.

DMX Controller

for 12V

24V products

Chassis part XLR-3 female

MUST

-Page 5-

-Page 4-

-Page 5-

DecaLED Setup Tool

A LED Setup Tool

(XB-R1)

Only a maximum loading capacity of 3A(1A

Only 50pcs DecaLED RGB modules

per individual channel) is allowed on a single

are allowed on a single output and the

output and the maximum amount of the total

maximum amount of connected modules

load can not exceed 4.5A distributed over all

can not exceed 250pcs.

2 outputs.

nly a maximum loading capacity o

nly a maximum loading capacity of

3-polar terminal connector

5-polar terminal connector

4-polar terminal connector

be used for signal connection.

A LED Setup Tool

(XB-R1)

Only a maximum loading capacity of 3A(

per individual channel) is allowed on a s

output and the maximum amount of the

load can not exceed 12A distributed ove

8 outputs.