Green Brook Phoenix ELTSLED65NM Installation & Operating Instructions

Browse online or download pdf Installation & Operating Instructions for Lighting Equipment Green Brook Phoenix ELTSLED65NM. Green Brook Phoenix ELTSLED65NM 2 pages.

Print Page
EMERGENCY LUMINAIRE TEST RECORD SHEET
LUMINAIRE TYPE/REF:_________________________________
DATE OF INSTALLATION:_______________________________
LOCATION:________________________
1st Year
Month
Test
Signed Date Signed Date Signed Date Signed Date Signed Date
1
Functional
2
Functional
3
Functional
4
Functional
5
Functional
6
Functional
7
Functional
8
Functional
9
Functional
10
Functional
11
Functional
Three Hour
12
Functional
TECHNICAL INFORMATION
Power Rating:
230V/240V AC - 50Hz
Colour Temp:
6500K
Power
Maintained 5.4W
Consumption:
Lamp type:
LED Non-replaceable
Lumen Output
Battery 590 lm
(Emergency mode)
Battery Life at 20°C:
> 4 years
Class Type:
1
Operating Temp Range: 0°C - 40°C
Emergency Light
Response Time (S):
1 second
Battery Type:
Ni-Cd 3.6V / 6000mAh
Battery Operating
Temp Range:
0°C - 45°C
Charge Time:
24 hours
Knockouts:
20mm
Product Weight:
1630g
Conforms To:
BS EN60598-2-22
2nd Year
3rd Year
4th Year
GUARANTEE
Your GreenBrook IP65 Twin Spot
is guaranteed for 3 years from the
date of purchase.
This is in addition to your statutory rights.
PLEASE KEEP THESE INSTRUCTIONS SAFE
FOR FUTURE REFERENCE
WEST ROAD . HARLOW
ESSEX . CM20 2BG . UK
www.greenbrook.co.uk
Instructions for 'Phoenix' Range IP65 Twin Spot - ELTSLED65NM
5th Year
This unit should be fitted by a qualified electrician in accordance with the appropriate
national/IET wiring regulations. Switch off mains supply before installation and maintenance.
This product must not be modified. Any modification will negate any Safety Mark Approvals and may
render the product unsafe. GreenBrook accepts no responsibility for modified products.
This product must be installed in accordance with these instructions. This fitting should not be installed in
close proximity to any external source of heat or covered with any heat insulating material, air flow
around the fitting should not be restricted. Note any minimum distances to adjacent surfaces. This unit
should be connected to the lighting supply circuit, or fused at a maximum of 5A.
This unit is a non-maintained (NM suffix), self-contained emergency luminaire.
To confirm model type, check the data provided on the fitting and packaging.
ELTSLED65NM
Follow these instructions carefully to ensure safe and reliable operation. Retain this leaflet for future
reference. The emergency luminaire should be connected to a stable and permanent mains supply of
the correct rated voltage and frequency as stated on the product specification label. This may be from
the lighting supply circuit, or fused at a maximum of 5A. To facilitate testing a fused spur box can be
included in the unswitched permanent live supply.
Class I. This product must be earthed.
All switching etc, shall comply with BS 5266 Part 1. Unless specifically permitted, emergency luminaires
should not be connected or controlled by any energy management device.
Before commencing installation, ensure that the electricity supply is disconnected. Surge suppressors
may be required at the point of connection to the supply wiring when installing luminaires to MICC
cable.
1. Undo the four cover retaining screws and remove the front cover.
2. Select and remove a knock out corresponding with the conduit and / or cable run and secure a
suitable bush within the hole to prevent damage to the incoming cable.
3. Mount the case in position on a suitable surface ensuring an adequate airflow will be maintained
around it, or secure to wall using the four hole dimensions on the back case.
Installation & Operating
SAFETY
GENERAL DESCRIPTION
Non-maintained:
Incorporates two 54 LED lamps which are
illuminated only under mains failure conditions, with
self test function.
INSTALLATION INSTRUCTIONS
NON-MAINTAINED
GREEN/YELLOW
NEUTRAL
(BLUE)
N
EARTH
E
PERMANENT LIVE
L
(BROWN)