IKEA IBD550PRS02 Installation Instructions Manual - Page 4

Browse online or download pdf Installation Instructions Manual for Oven IKEA IBD550PRS02. IKEA IBD550PRS02 16 pages. 30" (76.2 cm) electric single and double built-in oven

Print Page
IKEA IBD550PRS02 Installation Instructions Manual
Ifcodes permit and a separate ground w ire isused, i tis
recommended
thataqualified electrical installer determine that
theground p ath and wire gauge a reinaccordance
withlocal
codes.
Check w ithaqualified electrical installer ifyouarenotsure the
oven isproperly grounded.
This oven must b econnected toagrounded metal, permanent
wiring system.
Besure that t heelectrical connection and wire size areadequate
and inconformance
withtheNational Electrical Code, ANSI/NFPA
70-latest edition o rCSA Standards C22.1-94, Canadian Electrical
Code, Part 1 and C22.2 No. O -M91-1atest
edition, and alllocal
codes a nd ordinances.
Acopy oftheabove c ode standards canbeobtained from:
National Fire Protection Association
One Batterymarch
Park
Quincy, MA02269
CSA International
8501 East P leasant Valley R oad
Cleveland, OH 44131-5575
Electrical
Connection
To properly install your oven, you must determine the type of
electrical connection you will be using and follow the instructions
provided for it here.
•
Oven must be connected to the proper electrical voltage and
frequency as specified on the model/serial
number rating
plate. The model/serial number rating plate is located at the
bottom of the right-hand mounting rail. See the following
illustration.
A
Single Oven
A. Model/serial
number plate
Double Oven
A. Model/serial
number plate
Models rated from 7.3 to 9.6 kW at 240 volts (5.5 to 7.2 kW
at 208 volts) require a separate 40-amp circuit. Models rated
at 7.2 kW and below at 240 volts (5.4 kW and below at
208 volts) require a separate 30-amp circuit.
A time-delay fuse or circuit breaker is recommended.
Connect directly to the fused disconnect
(or circuit breaker
box) through flexible, armored or nonmetallic sheathed,
copper cable (with grounding wire). See "Make Electrical
Connection"
section.
Flexible cable from the oven should be connected directly to
the junction box.
Fuse both sides of the line.
Do not cut the conduit. The length of conduit provided is for
serviceability of the oven.
A UL listed or CSA approved conduit connector must be
provided.
•
If the house has aluminum wiring follow the procedure below:
1. Connect a section of solid copper wire to the pigtail
leads.
2. Connect the aluminum wiring to the added section of
copper wire using special connectors
and/or tools
designed and UL listed for joining copper to aluminum.
Follow the electrical connector manufacturer's
recommended
procedure. Aluminum/copper
connection must conform with
local codes and industry accepted wiring practices.
INSTALLATIONINSTRUCTIONS
1. Decide on the final location for the oven. Locate existing
wiring to avoid drilling into or severing wiring during
installation.
Excessive Weight Hazard
Use two or more people to move and install oven.
Failure to do so can result in back or other injury.
2.
To avoid floor damage, set the oven onto cardboard prior to
installation. Do not use handle or any portion of the front
frame for lifting.
On models with shipping feet attached:
To avoid product damage, do not remove the shipping feet at
the front lower corners of the oven. The shipping feet will
protect the lower oven trim until the oven is inserted into
cabinet.
3. Remove the shipping materials and tape from the oven.
4. Remove the hardware package from inside the bag containing
literature.
5. Remove and set aside racks and other parts from inside the
oven.
6. Move oven and cardboard close to the oven's final location.
R®
Oven T/ m
IMPORTANT." Use both hands to remove oven doors.
1. Open the oven door.
2. Locate the oven door latches in both corners of the oven door,
and rotate the latches forward to the unlocked position.
A. Oven door latch in locked
position
B. Oven door latch in unlocked
position