IKEA ISC23CDEXB00 User Instructions - Page 6

Browse online or download pdf User Instructions for Refrigerator IKEA ISC23CDEXB00. IKEA ISC23CDEXB00 40 pages.

Print Page

@ _J

Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced.

The quality of your ice will be only as good as the quality of the

water supplied to your ice maker. Avoid connecting the ice

maker to a softened water supply. Water softener chemicals

(such as salt) can damage parts of the ice maker and lead to

poor quality ice. If a softened water supply cannot be avoided,

make sure the water softener is operating properly and is well

maintained.

Do not use anything sharp to break up the ice in the storage

bin. This can cause damage to the ice container and the

dispenser mechanism.

Do not store anything on top of or in the ice maker or storage

bin.

Style I

Turning the Ice Maker On/Off:

The On/Off switch can only be accessed when the ice storage bin

has been removed. The switch is located on the freezer door, on

the left side of the wall that surrounds the ice storage bin. See the

following section for bin removal instructions.

•

To turn on the ice maker, slide the control to the ON (left)

position.

•

To manually turn off the ice maker, slide the control to the OFF

(right) position.

NOTE: The ice maker has an automatic shutoff to keep the

storage bin from overfilling during normal operation. The ice

maker sensors will automatically stop ice production,

but the

control will remain in the ON (left) position.

Removing

and Replacing

Ice Storage Bin:

1. Press down the release lever and tilt the bucket outward. Use

both hands to hold the base of the storage bin, then lift it up

and out.

Style 2

Turning the Ice Maker On/Off:

•

To turn ON the ice maker,simply lower the wire shutoff arm.

•

To manually turn off the ice maker, lift the wire shutoff arm to

the OFF (arm up) position and listen for the click. Ice can still

be dispensed, but no more can be made.

NOTE: The ice maker has an automatic shutoff to keep the

storage bin from overfilling during normal operation. As ice is

made, the ice cubes will fill the ice storage bin, and the ice cubes

will raise the wire shutoff arm to the OFF (arm up) position. Do not

force the wire shutoff arm up or down.

Removing

and Replacing

Ice Storage

Bin:

1. Pull the covering panel up from the bottom.

2. Lift the wire shutoff arm so it clicks into the OFF (up) position.

3. Lift up the front of the storage bin and pull it out.

Replace the bin by pushing it in all the way or the dispenser

will not work.

To restart ice production,

push the wire shutoff arm down to

the ON position. Make sure the door is closed tightly.

Do not use with water that is microbiologically

unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

A. Release lever

NOTE: It is not necessary to turn the ice maker control to the

OFF (right) position when removing the storage bin. The

sensor cover ("flipper door"), located on the right wall of the

freezer door, stops the ice maker from producing ice if the

door is open or the storage bin is removed.

Replace the bin by sliding it onto the door, then tilting it back

into an upright position. The release lever will click when the

bin is securely in place.

Water Filter Status Light

The water filter status light will help you know when to change

your water filter.

•

When the dispenser control panel's water filter status display

changes to "ORDER," this tells you that it is almost time to

change the water filter cartridge.

•

Replace the water filter cartridge when the water filter status

display changes to "REPLACE."

If water flow to your water dispenser or ice maker decreases

noticeably, change the filter sooner. The filter should be replaced

at least every 6 months, depending on your water quality and

usage.

•

After changing the water filter, reset the status light by

pressing and holding the FILTER button for 3 seconds. When

the system is reset, the "ORDER" and "REPLACE" icons will

disappear from the display screen.