Airflow Uno hab Installation Kit - Page 9

Browse online or download pdf Installation Kit for Heating System Airflow Uno hab. Airflow Uno hab 16 pages. Cavity wall decentralised mechanical ventilation with heat recovery unit
Also for Airflow Uno hab: Installation And Operating Instructions Manual (16 pages), Instructions (2 pages), Maintenance Manual (2 pages)

Print Page

WARNING

Installation - standard external grille

(can be shortened to min 300mm)

Internal wall

Wall installation sleeve

Fixing wedge

EPP wedge for

consendate drain

Cable conduit

SECTIONAL VIEW with horizontal core hole

wall sleeve

cut-out for

connection cable

condensate drain wedge

1. Insert wall sleeve in the

wall hole. Make sure the

condensate wedge is centrally

aligned with the cable conduit

and located at the bottom.

5. Cut the excess wall sleeve

length, wedges and foam flush

to the outside wall using an

oscillating saw blade tool.

Exception to this is if the wall

thickness is 250mm (see Fig.6).

9. When inserting the unit, do

not push hard into the external

grille and leave it where it stops.

This allows a free path for the air

to be exhausted/extracted.

13. Plug in the two-part

connector. Stow the

connection cable in the

allocated EPP shell space.

The wall sleeve must not be shortened on the inside of the wall, as the cut-out for feeding the power supply cable is

located here (see Fig. 5 & 6)!

When using the deep version external grille (Part no: 90001004), a wall sleeve protrusion of 50mm to the outside of

the wall must be taken into account (see . Fig. 6)

If necessary, the thickness of the plaster or wall covering should be taken into account.

500/800

External wall

Insulation foam

installation wedge

cable

channel

condensate drain wedge

2. Fix the wall sleeve on the

inside and outside of the wall

using the installation wedges,

supplied in the box.

Sealing compound

6. Seal the gap (same as in

image 4) and even off the

outside wall surface.

Cable length:

Distance = edge

of the wall insulation

sleeve to fan unit

Cable

10. Measure and cut the cable to

length.

14. Push the unit back until it

stops into the external grille

protection guard. (see point 9

for guidance)

Unohab Cavity Wall Installation Kit

Installation - deeper external grille

Internal wall

Wall installation sleeve

min.300 mm

Fixing wedge

EPP wedge for

consendate drain

Cable conduit

SECTIONAL VIEW with horizontal core hole

3. Fill in the gap between the core

hole and the wall sleeve with

insulation foam, including the

inside and outside of the wall.

Allow time to dry and remove

the wedges and excess foam.

Wall installation

sleeve

Cable

routing to

the

controller

7. Mount the external grille.

Detailed instructions are

provided in the Unohab

external grille manual, number

800001043 which can be

downloaded at airflow.com

Pull-out strap

Two-part

connector

11. Pull the unit out so the front of

the unit is flush with the hole,

before making the electrical

connection.

15. Insert the internal grille. Make

sure it is the correct way up,

indicated by the Airflow logo.

Installation and Operating Instructions

Wall thickness

min. 250mm

External wall

Insulation foam

50 -5

Protrusion of wall installation

sleeve

Cut out allocated

space for the

connection cable

4. Seal the gap to become water

proof.

'TOP'

External

grille

8. From the internal wall side,

slide the unit in the wall sleeve.

Make sure the 'TOP' marking

will be located on the top as

indicated.

Controller

cable (not

included in

the box)

Two-part

connector

12. Wire the controller cable wires

(max. outer Ø 6 mm) as per the wiring

diagrams which can be found in the

Unohab unit manual, number 80000777

which can be downloaded at

airflow.com

m Electrical connection:

If a residual current device is installed

in the EC fan power supply cable, it

must have the following technical

characteristics:

Type A or B with a rated differential

current of 30 mA.

The EC fan has a leakage current of <=

3.5mA, determined according to DIN

EN 50178.

Fig.6

Unit connection cable