IKEA IHW2530BS1 Installation Instructions And Use & Care Manual - Page 5

Browse online or download pdf Installation Instructions And Use & Care Manual for Ventilation Hood IKEA IHW2530BS1. IKEA IHW2530BS1 48 pages. 30" (76.2 cm) wall-mount canopy range hood

Print Page

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed here.

Tools needed

■

Level

Drill with 1¼" (3.0 cm), ³⁄₈" (9.5 mm), and ⁵⁄₁₆" (7.9 mm) drill bits

■

Pencil

■

Wire stripper or utility knife

■

Tape measure or ruler

■

Pliers

■

Caulking gun and weatherproof caulking compound

■

Vent clamps

■

Jigsaw or keyhole saw

■

Flat-blade screwdriver

■

Metal snips

■

Phillips screwdriver

Parts needed

■

Home power supply cable

■

½" (12.7 mm) UL listed or CSA approved strain relief

■

3 UL listed wire connectors

For vented installations, you will also need:

■

1 wall or roof cap

■

Metal vent system

For non-vented (recirculating) installations, you will also need:

■

Charcoal Filter Kit Part Number W10412939 for non-vented

(recirculating) installations only. See "Assistance or Service"

section to order.

■

6" (15.2 cm) dia. round metal vent duct - length required

is determined by ceiling height.

Parts supplied

Remove parts from packages. Check that all parts are included.

■

Hood canopy assembly with blower, light bulbs, and canopy

glass already installed

■

Vent transition with back draft dampers installed

■

Metal grease filter

■

Vent cover support bracket

■

Mounting template

■

2-piece vent cover

■

Air deflector (for non-vented [recirculating] installations only)

■

8 - 4.2 x 8 mm screws (T20

■

6 - 5 x 45 mm mounting screws (#2 Phillips drive)

■

2 - 8 x 40 mm wall anchors (masonry)

■

4 - 10 x 60 mm wall anchors

■

4 - 5.4 x 75 mm screws (for 10 x 60 mm wall anchors)

■

2 - 3.5 x 9.5 mm screws (T10 drive)

■

®†

T10 Torx

adapter

■

T20

Torx

adapter

†®TORX and T20 are registered trademarks of Acument Intellectual Properties, LLC.

INSTALLATION REQUIREMENTS

®†

drive)

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

Have a qualified technician install the range hood. It is the

installer's responsibility to comply with installation clearances

specified on the model/serial/rating plate. The model/serial/rating

plate is located behind the left filter on the rear wall of the vent

hood.

Canopy hood location should be away from strong draft

areas, such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used.

Given dimensions provide minimum clearance.

Grounded electrical outlet is required. See "Electrical

Requirements" section.

The canopy hood is factory set for venting through the roof or

wall. For non-vented (recirculating) installation, see "For non-

vented (recirculating) installation only" in the "Connect Vent

System" section. Charcoal Filter Kit Part Number W10412939

is available from your dealer or an authorized parts distributor.

All openings in ceiling and wall where canopy hood will be

installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title 24

CFR, Part 328 (formerly the Federal Standard for Mobile Home

Construction and Safety, Title 24, HUD, Part 280) or when such

standard is not applicable, the standard for Manufactured Home

Installation 1982 (Manufactured Home Sites, Communities and

Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local

codes.

Product Dimensions

10⁷⁄₈" (27.6 cm)

4⁷⁄₈" (12.3 cm)

13³⁄₁₆" (33.5 cm)

30" (76.2 cm)

*For non-vented (recirculating) installations

**For vented installations

5¹⁵⁄₁₆" (15.0 cm)

*27⁷⁄₈" (70.8 cm) min.

46⁹⁄₁₆" (118.3 cm) max.

21"

(53.3 cm)

14³⁄₄"

**27⁷⁄₈" (70.8 cm) min.

(37.6 cm)

42³⁄₄" (108.6 cm) max.

1¹³⁄₁₆"

(4.6 cm)

19¹¹⁄₁₆" (50.0 cm)