IKEA 504.756.23 Manual - Page 7
Browse online or download pdf Manual for Dishwasher IKEA 504.756.23. IKEA 504.756.23 33 pages.
Print Page
1
Soft
2
Medium
ENGLISH
3
Average
4
Hard
5
Very hard
Filling the rinse aid dispenser
• Switch off the appliance by pressing the ON/OFF button.
Rinse aid makes dish DRYING easier. The rinse aid dispenser A
Setting is complete!
should be filled when the RINSE AID REFILL indicator light
the control panel is lit.
ENGLISH
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DRYING easier. The rinse aid dispenser A
should be filled when the RINSE AID REFILL indicator light
Make sure the cap is screwed on tightly, so that no detergent can
in the control panel is lit.
ENGLISH
get into the container during the wash program (this could damage
the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The "Pre-Wash" program alone is NOT
Make sure the cap is screwed on tightly, so that no detergent can
Residual saline solution or grains of salt can lead to corrosion,
get into the container during the wash program (this could damage
irreparably damaging the stainless steel components.
B
B
the water softener beyond repair).
The guarantee is not applicable if faults are caused by such
As soon as this procedure is complete, run a program without
1. Open the dispenser
B
circumstances.
loading. The "Pre-Wash" program alone is NOT
the lid.
Residual saline solution or grains of salt can lead to corrosion,
2. Carefully introduce the rinse aid as far as the maximum (110
irreparably damaging the stainless steel components.
B
heating element may be damaged as a result.
ml) reference notch of the filling space avoid spilling it. If this
The guarantee is not applicable if faults are caused by such
Whenever you need to add salt, it is mandatory to complete
1. Open the dispenser B by pressing and pulling up the tab on
happens, clean the spill immediately with a dry cloth.
circumstances.
the procedure before the beginning of the washing cycle.
3. Press the lid down until you hear a click to close it.
the lid.
NEVER pour the rinse aid directly into the tub.
2. Carefully introduce the rinse aid as far as the maximum
SETTING THE WATER HARDNESS
heating element may be damaged as a result.
(110 ml) reference notch of the filling space - avoid spilling it.
To allow the water softener to work in a perfect way, it is essential
Whenever you need to add salt, it is mandatory to complete
Adjusting the dosage of rinse aid
If this happens, clean the spill immediately with a dry cloth.
that the water hardness setting is based on the actual water hard-
the procedure before the beginning of the washing cycle.
If you are not completely satisfied with the drying results, you
ness in your house. This information can be obtained from your local
3. Press the lid down until you hear a click to close it.
can adjust the quantity of rinse aid used.
water supplier. The factory setting is for average (3) water hardness.
NEVER pour the rinse aid directly into the tub.
SETTING THE WATER HARDNESS
• Switch the dishwasher on using the ON/OFF button.
To allow the water softener to work in a perfect way, it is essential
• Switch on the appliance by pressing the ON/OFF button.
• Switch it off using the ON/OFF button.
that the water hardness setting is based on the actual water hard-
• Switch off the appliance by pressing the ON/OFF button.
• Press button
three times a beep will be heard.
ness in your house. This information can be obtained from your local
• Hold down button
for 5 seconds, until you hear a beep.
• Switch it on using the ON/OFF button.
water supplier. The factory setting is for average (3) water hardness.
• Switch on the appliance by pressing the ON/OFF button.
•
The current selection level number and the salt indicator light
• The current selection level number and rinse aid indicator
• Switch on the appliance by pressing the ON/OFF button.
light flash.
• Switch off the appliance by pressing the ON/OFF button.
•
Press button
to select the desired hardness level (see
• Press button
to select the level of rinse aid quantity to be
• Hold down button
for 5 seconds, until you hear a beep.
WATER HARDNESS TABLE).
supplied.
• Switch on the appliance by pressing the ON/OFF button.
Water Hardness Table
•
The current selection level number and the salt indicator light
• Switch it off using the ON/OFF button.
Setting is complete!
Level
•
Press button
to select the desired hardness level (see
German degrees
If the rinse aid level is set to ZERO (ECO), no rinse aid will be
WATER HARDNESS TABLE).
1
Soft
supplied. The LOW RINSE AID indicator light will not be lit if you
Water Hardness Table
2
Medium
run out of rinse aid. A maximum of 5 levels can be set according
3
Average
Level
to the dishwasher model. The factory setting is specific to the
German degrees
model, please follow instruction above to check this for your
4
Hard
1
Soft
machine.
5
Very hard
2
Medium
• If you see bluish streaks on the dishes, set a low number (12).
3
Average
• If there are drops of water or limescale marks on the dishes,
• Switch off the appliance by pressing the ON/OFF button.
Setting is complete!
set a high number (34).
4
Hard
5
Very hard
FILLING THE RINSE AID DISPENSER
Filling the detergent dispenser
Rinse aid makes dish DRYING easier. The rinse aid dispenser A
Usage of detergent not designed for dishwashers may cause
• Switch off the appliance by pressing the ON/OFF button.
should be filled when the RINSE AID REFILL indicator light
Setting is complete!
malfunction or damage to the appliance.
in the control panel is lit.
To open the detergent dispenser press button C.
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DRYING easier. The rinse aid dispenser A
should be filled when the RINSE AID REFILL indicator light
Control panel
in the control panel is lit.
B
1. Open the dispenser B by pressing and pulling up the tab on
the lid.
2. Carefully introduce the rinse aid as far as the maximum
(110 ml) reference notch of the filling space - avoid spilling it.
B
If this happens, clean the spill immediately with a dry cloth.
1. Open the dispenser B by pressing and pulling up the tab on
1
2
3 4
3. Press the lid down until you hear a click to close it.
the lid.
NEVER pour the rinse aid directly into the tub.
2. Carefully introduce the rinse aid as far as the maximum
(110 ml) reference notch of the filling space - avoid spilling it.
1
OnOff/Reset button with indicator light
If this happens, clean the spill immediately with a dry cloth.
2
Program selection button
3. Press the lid down until you hear a click to close it.
3
NEVER pour the rinse aid directly into the tub.
Salt refill indicator ligh
4
Rinse Aid refill indicator ligh
5
Program number and delay time indicator
6
Tablet indicator light
7
Display
German degrees
French degrees
0 - 6
11
7 - 11
12 - 17
18 - 34
Control panel
35 - 50
1
2
1.
On-Off/Reset button with indicator light
2.
Program selection button
3.
Salt refill indicator ligh
4.
Rinse Aid refill indicator ligh
A
A
5.
Program number and delay time indicator
6.
Tablet indicator light
by pressing and pulling up the tab on
First use
A
ADVICE REGARDING THE FIRST TIME USE
After installation, remove the stoppers from the racks and the
retaining elastic elements from the upper rack.
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the
dishes andon the machine's functional components.
• It is important that the salt reservoir be never empty.
• It is important to set the water hardness.
The salt reservoir is located in the lower part of the
dishwasher (see PRODUCT DESCRIPTION) and should be
filled when the SALT REFILL indicator light
control panel is lit .
°dH
°fH
French degrees
0 - 6
0 - 10
7 - 11
11 - 20
°dH
°fH
12 - 17
21 - 30
French degrees
18 - 34
31 - 60
0 - 6
0 - 10
35 - 50
61 - 90
7 - 11
11 - 20
12 - 17
21 - 30
18 - 34
31 - 60
35 - 50
61 - 90
A
h
A
6
8
9
10
5
7
To download the full version visit www.ikea.com
Exceeding the stated amount does not result in a more effective
wash and increases environmental pollution.
0 - 10
The amount can be adjusted to the soil level. In the case of
11 - 20
normally soiled items, use approximately either 35g (powder
21 - 30
detergent) or 35ml (liquid detergent) and additional tea spoon of
detergent directly inside the tub. If tablets are used, one tablet
31 - 60
will be enough.
61 - 90
If the crockery is only lightly soiled or if it has been rinsed with
Introduce the detergent into the dry dispenser D only.
water before being placed in the dishwasher, reduce the amount
Place the amount of detergent for
of detergent used accordingly (minimum 25 g/ml) e.g. skip the
h
pre-washing directly inside the tub.
in
powder/gel putted inside the tub.
3 4
5
6 7 8
9
ADJUSTING THE DOSAGE OF RINSE AID
B
If you are not completely satisfied with the drying results, you can
D
adjust the quantity of rinse aid used.
A
• Switch the dishwasher on using the ON/OFF button.
C
• Switch it off using the ON/OFF button.
ADJUSTING THE DOSAGE OF RINSE AID
• Press button
three times - a beep will be heard.
If you are not completely satisfied with the drying results, you can
• Switch it on using the ON/OFF button.
adjust the quantity of rinse aid used.
•
The current selection level number and rinse aid indicator light flash.
• Switch the dishwasher on using the ON/OFF button.
•
Press button
to select the level of rinse aid quantity to be
• Switch it off using the ON/OFF button.
s.
supplied.
• Press button
three times - a beep will be heard.
1.
When measuring out the detergent refer to the mentioned ear-
1. When measuring out the detergent refer to the mentioned
• Switch it off using the ON/OFF button.
• Switch it on using the ON/OFF button.
earlier information to add the proper quantity. Inside the
lier information to add the proper quantity. Inside the dispenser
Setting is complete!
•
The current selection level number and rinse aid indicator light flash.
dispenser
B there are indications to help the detergent dosing.
If the rinse aid level is set to ZERO (ECO), no rinse aid will be
•
Press button
to select the level of rinse aid quantity to be
dosing.
2.
Remove detergent residues from the edges of the dispenser
supplied. The LOW RINSE AID indicator light will not be lit if you
s.
supplied.
2. Remove detergent residues from the edges of the dispenser
run out of rinse aid. A maximum of 5 levels can be set according to
and close the cover until it clicks.
• Switch it off using the ON/OFF button.
the dishwasher model. The factory setting is specific to the model,
and close the cover until it clicks.
Setting is complete!
3. Close the lid of the detergent dispenser by pulling it up until
please follow instruction above to check this for your machine.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
If the rinse aid level is set to ZERO (ECO), no rinse aid will be
• If you see bluish streaks on the dishes, set a low number (1-2).
the closing device is secured in place.
supplied. The LOW RINSE AID indicator light will not be lit if you
• If there are drops of water or limescale marks on the dishes,
The detergent dispenser automatically opens up at the right time
run out of rinse aid. A maximum of 5 levels can be set according to
The detergent dispenser automatically opens up at the right
set a high number (3-4).
the dishwasher model. The factory setting is specific to the model,
according to the program. If all-in-one detergents are used, we
time according to the program. If allinone detergents are used,
please follow instruction above to check this for your machine.
recommend using the TABLET button, because it adjusts the
we recommend using the TABLET button, because it adjusts the
• If you see bluish streaks on the dishes, set a low number (1-2).
FILLING THE DETERGENT DISPENSER
program so that the best washing and drying results are always
program so that the best washing and drying results are always
• If there are drops of water or limescale marks on the dishes,
achieved.
achieved.
set a high number (3-4).
dishwashers.
in the
To achieve the best washing and drying results, the combined
useof detergent, rinse aid liquid and refined salt is required.
FILLING THE DETERGENT DISPENSER
We recommend using detergents that do not contain phosphates
or chlorine, as these products are harmful to the environment.
dishwashers.
Good washing results also depend on the correct amount of
To achieve the best washing and drying results, the combined
detergent being used.
useof detergent, rinse aid liquid and refined salt is required.
Exceeding the stated amount does not result in a more effective
We recommend using detergents that do not contain phosphates
wash and increases environmental pollution.
or chlorine, as these products are harmful to the environment.
The amount can be adjusted to the soil level. In the case of
Good washing results also depend on the correct amount of
normally soiled items, use approximately either 35g (powder
detergent being used.
detergent) or 35ml (liquid detergent) and additional tea spoon of
Exceeding the stated amount does not result in a more effective
detergent directly inside the tub. If tablets are used, one tablet
wash and increases environmental pollution.
will be enough.
The amount can be adjusted to the soil level. In the case of
If the crockery is only lightly soiled or if it has been rinsed with
normally soiled items, use approximately either 35g (powder
water before being placed in the dishwasher, reduce the amount
detergent) or 35ml (liquid detergent) and additional tea spoon of
of detergent used accordingly (minimum 25 g/ml) e.g. skip the
detergent directly inside the tub. If tablets are used, one tablet
powder/gel putted inside the tub.
will be enough.
If the crockery is only lightly soiled or if it has been rinsed with
water before being placed in the dishwasher, reduce the amount
of detergent used accordingly (minimum 25 g/ml) e.g. skip the
powder/gel putted inside the tub.
B
A
B
A
1.
When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity. Inside the dispenser
B there are indications to help the detergent dosing.
2.
Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
1.
When measuring out the detergent refer to the mentioned ear-
3sec
3. Close the lid of the detergent dispenser by pulling it up until
lier information to add the proper quantity. Inside the dispenser
the closing device is secured in place.
B there are indications to help the detergent dosing.
11
12
13
2.
Remove detergent residues from the edges of the dispenser
The detergent dispenser automatically opens up at the right time
and close the cover until it clicks.
according to the program. If all-in-one detergents are used, we
3. Close the lid of the detergent dispenser by pulling it up until
recommend using the TABLET button, because it adjusts the
8
Flexible Wash indicator light
the closing device is secured in place.
program so that the best washing and drying results are always
9
Flexible Wash button
achieved.
The detergent dispenser automatically opens up at the right time
10
Delay button
according to the program. If all-in-one detergents are used, we
11
Short Time button with indicator light
recommend using the TABLET button, because it adjusts the
program so that the best washing and drying results are always
12
Extra Dry button with indicator light
achieved.
13
START/Pause button with indicator light / Tab
3sec
8
To open the detergent dispenser
press button A.
10
11
Introduce the detergent into
8
the dry dispenser B only.
7.
Display
Place the amount of detergent
8.
Half Load indicator light
for pre-washing directly inside
9.
Half Load button
the tub.
10. Delay button
11. START/Pause button with indicator light / Tab
there are indications to help the detergent
D
To open the detergent dispenser
press button A.
Introduce the detergent into
the dry dispenser B only.
Place the amount of detergent
To open the detergent dispenser
for pre-washing directly inside
press button A.
the tub.
Introduce the detergent into
the dry dispenser B only.
Place the amount of detergent
for pre-washing directly inside
the tub.
1
2
3
4
5
6
7
50°
50°-60°
65°
50°
50°
45°
50°
7
1. Remove the lower rack and
unscrew the reservoir cap
(anticlockwise).
2. Only the first time you do this: fill
the salt reservoir with water.
3. Position the funnel (see figure)
and fill the salt reservoir right up
to its edge (approximately 1 kg);
it is not unusual for a little water to
leak out.
4. Remove the funnel and wipe any
salt residue away from the
opening.
8
9
10
65°
65°
10 PROGRAMS