IKEA LAGAN Manual - Page 12

Browse online or download pdf Manual for Dishwasher IKEA LAGAN. IKEA LAGAN 24 pages. Examples of the load of the basket
Also for IKEA LAGAN: Assembly Instructions Manual (8 pages), User Manual (20 pages), User Manual (16 pages), User Manual (20 pages), Instructions Manual (48 pages), User Manual (16 pages), User Manual (24 pages), Manual (28 pages), Instruction Manual (24 pages), User Manual (24 pages), Manual (4 pages), User Manual (12 pages), Manual (24 pages), Assembly Instructions Manual (20 pages), Installation Manual (20 pages), Manual (28 pages), Manual (32 pages), Manual (44 pages), Manual (16 pages), Manual (16 pages), Manual (24 pages), Manual (28 pages), Manual (28 pages), User Manual (28 pages), Manual (40 pages), Manual (48 pages), Use & Care Manual (25 pages), Manual (44 pages), Manual (40 pages), Manual (28 pages), Manual (28 pages), User Manual (24 pages), Manual (48 pages), User Manual (16 pages), Installation Instructions Manual (18 pages), Manual (48 pages), Quick Start Manual (4 pages), Installation Instructions Manual (16 pages), Manual (28 pages), Manual (28 pages), Manual (44 pages), Manual (48 pages), Manual (16 pages), Manual (32 pages), Manual (24 pages), Manual (25 pages), Manual (18 pages), User Manual (28 pages), Manual (44 pages), Manual (24 pages), Manual (32 pages), Manual (18 pages), Manual (48 pages), Manual (29 pages), Manual (29 pages), Manual (34 pages), Installation Instructions Manual (42 pages)

Print Page

ENGLISH

Installation

After unpacking the hob, make sure that it

has not been damaged during transport. In

the event of problems, contact the dealer or

your nearest After-sales Service.

Technical information for the installer

This product can be embedded in a

worktop 20 to 50 mm thick.

If there is no oven beneath the hob,

insert a separator panel that has a

surface at least equal to the opening

in the work surface. This panel must be

positioned in no case less than 20 mm

from the bottom of the hob.

Before installation, make sure that:

the local gas delivery conditions (nature

and pressure) are compatible with the

settings of the hob (see the rating plate

and injector table);

the outer surfaces of the furniture or

appliances adjacent to the hob are heat

resistant according to local regulations;

This appliance is not connected to a

fume exhaust device. It shall be installed

in accordance with current installation

regulations. Particular attention shall

be given to the relevant requirement

regarding ventilation.

Combustion products are discharged

outdoors through specific hoods or wall

and/or window mounted electrical fans.

Gas connection

This operation must be performed by a

qualified technician.

The gas supply system must comply with

local regulations to the relavant gas

standard.

You can find specific local regulations for

some countries in the paragraph

"Reference to Local Regulations". If no

information concerning your Country is

given, please ask details to a qualified

technician.

The connection of the hob to the gas

pipe network or gas cylinder must be

made by means of a rigid copper or

steel pipe with fittings complying with

local regulations, or by means of a

flexible hose assemby complying with

local regulations. The maximum length

of the hose is 2 linear metres.

The flexible hose assembly must be

an Australian approved Class B or D

flexible hose with 10mm I.D.

The hose should not be subjected

to abrasion, kinking or permanent

deformation and should be able to be

inspected along its entire length. Unions

compatible with the hose fittings must

be used and connections tested for gas

leaks.

- IMPORTANT: if a flexible hose assembly

is used, it must be installed so as not to

touch any mobile part of the furniture.

It must pass through an area where

there are no obstructions and where it is

possible to inspect it on all its length.

After connection to the gas supply, check

for leaks with soapy water. Light up the

burners and turn the knobs from max