IKEA UNDERCOUNTER DISHWASHER PLASTIC GIANT TUB MODELS Installation Instructions Manual - Page 3
Browse online or download pdf Installation Instructions Manual for Dishwasher IKEA UNDERCOUNTER DISHWASHER PLASTIC GIANT TUB MODELS. IKEA UNDERCOUNTER DISHWASHER PLASTIC GIANT TUB MODELS 44 pages.
Print Page
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools needed
■
Pliers
■
Phillips screwdriver
■
Flat-blade screwdriver
⁵⁄₁₆" and ¼" nut drivers or
■
hex sockets
■
Measuring tape or ruler
■
1½" hole saw bit
■
Twist-on wire connectors
[proper size to connect
household wiring to 16-
gauge wiring in
dishwasher] (2)
■
15 TORX
®†
screwdriver
(if installing custom front
panels)
Parts needed
90° elbow with ³⁄₈" N.P.T.
■
external threads on one
end. (The other end must
fit your water supply line.)
■
Teflon
®†
tape or pipe joint
compound
Tools needed (new installation)
■
Cordless drill
¹⁄₂", ³⁄₄" and 1¹⁄₂" hole saw
■
bits
Parts needed (new installation)
■
Copper tubing (³⁄₈"
recommended) or
■
Flexible stainless steel
braided fill line
Parts supplied
A
A. Drain hose clamps [1 large and 1 small] (2)
¹⁄₂"
B. #10 x
Phillips-head screws (2)
C. Drain hose
†®
TORX is a registered trademark of Acument Intellectual Properties, LLC
®
Teflon is a registered trademark of E.I. Dupont de Nemours and Company.
INSTALLATION REQUIREMENTS
■
10" adjustable wrench
(opens to 1¹⁄₈" [2.9 cm])
■
Utility knife
■
Level
■
Cordless drill
⁵⁄₈" open-end wrench
■
■
Flashlight
■
Shallow pan
■
Wood block
■
Bath towel
■
Shims
#10 x ¹⁄₂" wood screws
■
[if installing custom front
panels] (4)
■
Small tubing center
■
Wire stripper
■
1¹⁄₂" to 2" screw-type
clamp (if connecting to
waste-tee)
■
Clamp connector or
conduit connector
(to fit a ⁷⁄₈" [2.2 cm]
diameter hole)
B
C
Additional parts supplied (top-venting models only)
■
Bottom sound pad (located in lower rack)
■
Moisture barrier tape
Make sure all these parts are included. If not, call
1-866-664-2449.
See separate parts list for accessories available for your
dishwasher.
Location Requirements
Do not run drain lines, water lines or electrical wiring where they
can interfere with or contact the dishwasher motor or legs.
The location where the dishwasher will be installed must provide
clearance between motor and flooring. Motor should not touch
the floor.
Do not install dishwasher over carpeted flooring.
Shelter dishwasher and water lines leading to dishwasher against
freezing. Damage from freezing is not covered by the warranty.
A side panel kit is available from your dealer for installing your
dishwasher at the end of your cabinetry.
A moisture barrier accessory (Part Number 4396277) is available
from your dealer for installing underneath the countertop, but is
not required. Call 1-866-664-2449 for ordering.
Check location where the dishwasher will be installed. The
location must provide:
■
Easy access to water, electricity and drain.
■
Convenient access for loading and unloading dishes. Corner
locations require a 2" (5.1 cm) minimum clearance between
the side of the dishwasher door and the wall or cabinet.
■
Square opening for proper orientation.
■
Cabinet front perpendicular to floor.
■
Level floor. If the floor at the front of the dishwasher is not level
with the rear of the opening, shims may be needed to level the
dishwasher.
NOTE: To avoid shifting during dishwasher operation, shims
must be securely attached to the floor.
If the dishwasher will be left unused for a period of time or it is in a
location where it may be subject to freezing, have it winterized by
authorized service personnel.
Make sure pipes, wires and drain hose are within the shaded area
shown in the "Cutout dimensions" section.
Helpful Tip: If the floor in the dishwasher opening is uneven
(example: tile flooring only partway into opening), accurately
measure the dimensions and level the dishwasher.
3