ALIBI ALI-CD1720EC Quick Installation Manual - Page 2

Browse online or download pdf Quick Installation Manual for Security Camera ALIBI ALI-CD1720EC. ALIBI ALI-CD1720EC 2 pages. Hd-tvi/cvbs turret camera

Print Page

If the drop cable will route through a hole in the mounting surface, route the cable through the hole,

and then reassemble the camera on the mounting plate. Tighten the bezel only enough to hold the

assembly together, but do not tighten the bezel.

Connect the camera drop cable to video and power extension cables.

10.

Connect the CVBS leads to a toggle switch, if needed, or short them together for CVBS output at the

BNC connector. Seal the wires to protect from moisture.

11.

Connect the other end of the video extension cable to a HD-TVI compatible (or CVBS, if configured)

video monitoring device, such as a HD-TVI digital video recorder (DVR).

Drop cable connectors are not waterproof.

NOTE

12.

Connect the other end of the power extension cable to a 12 Vdc power source. Observe the polarity

of the cable shown in the photo on page 1 of this guide.

13.

Rotate the camera module so that the light sensor is at the bottom of the IR array, if necessary.

14.

While observing video from the camera on a monitor, aim the camera at your surveillance target.

See the figure below for adjustment ranges.

Cleaning

Clean the camera glass with an approved glass cleaning solution and a lint free cloth.

Dust can be removed from the unit by wiping it with a soft damp cloth. To remove stains, gently rub

•

the surface with a soft cloth moistened with a mild detergent solution, then rinse and dry it with a

soft cloth.

Remove all foreign particles, such as plastic or rubber materials, attached to the camera housing.

•

These may cause damage to the surface over time.

Do not use benzene, thinner or other chemical products on the camera assembly; these may



dissolve the paint and promote damage of the surfaces. Before using any chemical product,

CAUTION

carefully follow the accompanying instructions.

Troubleshooting

Problem

Nothing appears on the screen

The video image is dim or not clear.

The screen is dark.

The camera is not working properly and the

surface of the camera is hot.

The image on the monitor flickers

www.observint.com

Possible Cause

- Check the power connection.

- Check the video signal cable connection to the monitor.

- If the camera lens is dirty, clean it with a soft, clean cloth.

- Adjust the monitor controls, if necessary.

- If the camera is facing a very strong light, change the camera position.

- Adjust the contrast control of the monitor.

- Set the monitor impedance properly for the DVR (usually 75 Ω /Hi-Z),

and check the cable connections.

- Verify that the camera is correctly connected to an appropriate regulated

power source.

- Make sure that the camera isn't facing direct sunlight or fluorescent light.

If necessary,change the camera position.

Specifications

Camera

ALI-CD1720EC

Image Sensor

Progressive Scan CMOS

Effective Pixels

1280(H) * 720(V)

CVBS resolution

1000 TVL

Min. Illumination

0.01 lux @ (F1.2, AGC on), 0 lux with IR

Shutter Time

1/30 s to 1/50,000 s

Lens

3.6 mm Angle of View: 71°

Lens Mount

M12

Angle Adjustment

Pan: 0 ~ 360°, Tilt: 0 ~ 90°, Rotation: 0 ~ 360°

Day & Night

ICR

Synchronization

Internal synchronization

Video Frame Rate

720p @ 30 fps

HD Video Output

1 HD-TVI output or CVBS output

Enclosure color

White

General

-40 °F ~ 140 °F (-40 °C ~ 60 °C)

Working Temperature/Humidity

Humidity 90% or less (non-condensing)

Power Supply

12 Vdc

Power Consumption

Max. 4 W

Weather Proof Ratings

IP66

IR Range

Up to 65 ft (20 m)

Dimension

Φ3.52" × 2.75" (Φ89.5 × 69.8 mm)

Weight

0.57 lb (260 g)