JAMEC PEM 58.1045 Operating Instructions - Page 2
Browse online or download pdf Operating Instructions for Tools JAMEC PEM 58.1045. JAMEC PEM 58.1045 3 pages. Water hose reel retractable 20 m
Print Page
WATER HOSE REEL
PRO SERIES - RETRACTABLE 20 M
With the unique Helix Ultra-Coil hose layering system, combined with a precision
machined solid brass central spindle, the Jamec Pem Pro Series Hose Reels are
ideally suited for the trade or industrial workshop
FEATURES
Hose layering system
Auto lock / rewind
Solid brass internal spindle
Adjustable hose stop
Wall mount with 180° pivot
Weather resistant UV stabilised polypropylene case
Leader hose 2 m with brass fittings
Includes water trigger gun
SPECIFICATIONS
Hose length
Hose I.D
Hose O.D
Leader hose length
Hose material
Reel / case type
Auto lock / rewind
Max. working pressure
Fitting size
Bracket
Product dimensions
Weight
Application
MAINTENANCE
Always keep the hose clean.
If the hose becomes dirty, clean it with a damp cloth while retracting.
DO NOT twist the hose while in use.
Mount the hose reel in a sheltered area to assist and protect the performance of
the hose and hose reel.
DO NOT allow the hose to contact any corrosive chemicals or fluids.
Always retract the hose when not in use.
The Jamec Pem Water Hose Reel Pro Series Retractable contains a pre-tensioned
spring inside the inner drum assembly.
Do not attempt to open the inner drum assembly.
PRODUCT IDENTIFICATION
5
2
4
1
6
3
20 m
11.5 mm (1/2")
16 mm (5/8")
2 m Brass tap female fitting
Reinforced PVC braided
Retractable / polypropylene
Yes
150 psi
12 mm Tap fittings
180° Pivoting
440 L x 210 W x 400 H mm
8.2 kg
Water
Mounting bracket
1.
Optional fixed in-line
2.
locking plate
Pivot pin
3.
Fully enclosed case
4.
8
Carry handle
5.
Solid brass internal
6.
spindle
2 Metre leader hose
7.
9
Hose with adjustable
8.
stopper
Water gun
9.
7
0.8 metre min.
INSTALLATION
The Jamec Pem Water Hose Reel Pro Series Retractable can
be mounted in a horizontal or vertical position.
Chose a location that is near to the water source.
1.
For large areas, place the hose reel at the centre of the
2.
work area.
When mounting the hose reel vertically, ensure there is
3.
adequate clearance under the reel to prevent injury or
damage.
Mounting bracket must be installed on a flat surface.
4.
Note: It is recommended to install the mounting bracket
5.
0.8 metre (minimum) above the floor level.
Drill 4 x M8 holes to match the holes located in the
6.
Mounting Bracket.(Fig. 1)
Connect the hose reel to the Mounting Bracket with the
7.
Pivot Pin.(Fig. 2)
Note: For fixed in-line position, fit the locking plate onto the
Mounting Bracket prior to inserting the pivot pin. (Fig. 3)
Connect the inlet leader hose to the water source using
8.
the tap fittings supplied.
OPERATION
Slowly pull out the hose to the required length. A 'clicking' noise will be heard
1.
every revolution of the inner drum. To lock the reel, allow the hose to retract slowly
after hearing the second or third 'click'.
To release the hose, pull out the hose until the 'clicking' noise stops, and then
2.
allow the hose to slowly retract while guiding the hose back into the hose reel. The
self layering mechanism will coil the hose back onto the inner drum.
To avoid injury and damage, always hold the hose while it is retracting.
3.
IMPORTANT:
If the hose becomes tangled and will not retract - slowly pull out the hose
past the tangled section and then allow the hose to slowly retract while
guiding the hose back into the hose reel.
Always ensure the hose is clean and not twisted.
Fig. 1 Mounting Bracket
Fig. 2 Pivot Pin
Fig. 3 Locking Plate