Avantgarde UNO SD User Manual - Page 9

Browse online or download pdf User Manual for Speakers Avantgarde UNO SD. Avantgarde UNO SD 19 pages.

Print Page
Avantgarde UNO SD User Manual
CONNECTION – PASSIVE VERSION
SINGLE–WIRING
1 3
1 4
AMP SWITCH
MID
HIGH
MID
IN
OUT
SPEAKER TYPE
UNO G3
MODEL NO.
PASSIVE CROSSOVER SWITCH
ORIGIN
MADE IN GERMANY
1
1 2
High � and mid � have separate speaker terminals. In the standard
configuration these connectors interconnected with 2 x OFC 2-way
bridges �&�. One bridge � interconnects all "+" terminals, the
other bridge � interconnects all "-" terminals.
1
Connect the Speaker-Output of your power (or integrated) amplifier
to the Speaker-MID connector � of the speakers.
Connect the HIGH terminal � of the speaker and the speaker input
2
terminals of the DSP subwoofer amplifier with the jumper cable.
The jumper cable is included in the accessory box.
Only now connect the components' power cords to a household
3
outlet and turn on the subwoofer and other equipment.
The inputs and outputs of the AMP SWITCH � are exclusively
�
available on devices with ITRON amplifier (incl. the AMP SWITCH
circuitry) and are used for remote switching between PASSIVE cros‐
sover and ITRON amplifier.
SPEAKER TYPE
UNO G3
DUO G3
PUSH
MODEL NO.
ITRON AMP
ORIGIN
MADE IN GERMANY
only to be used with marked speaker type
+ 1.5
+ 1.5
0dB
ENGAGED
FUSE
– 1.5
– 1.5
RESET
MID
HIGH
IN
E FUSE
DRIVER GAIN
BALANCED INPUT
1 5
MID
MID
DUO G3
only to be used with marked speaker type
WARNING
ELECTRICAL SHOCK HAZARD
DO NOT OPEN!
110 – 240V ~ 50/60HZ
MAX POWER CONSUMPTION – 570W
POWER OUTPUT – 530W RMS
FUSE 2.5 A SLOW
+ 1.5
+ 3
+ 6
0dB
0dB
– 1.5
– 3
– 6
OUT
TOTAL GAIN
16
CONNECTION – PASSIVE VERSION
BI–WIRING
1 3
1 4
AMP SWITCH
MID
IN
OUT
To operate the system in BI-Wiring or BI-Amping mode, the 2 x OFC
1
2-way bridges �&� must be removed.
2
Open the screw caps of the tweeter � and midrange � speaker ter‐
minals and remove the two OFC 2-way bridges �&�.
3
Connect the speaker output of your power amplifier (or integrated
amplifier) to the speaker terminals of the loudspeaker, using a sepa‐
rate cable for each terminal. The same applies if you are using mul‐
tiple amplifiers for treble and midrange.
4
Connect the HIGH terminal � of the speaker and the speaker input
terminals of the DSP subwoofer amplifier with the jumper cable.
The jumper cable is included in the accessory box.
The jumper cables have hollow banana plugs which are open at
�
the rear. This way it is possible to stack multiple speaker cables to
the same speaker terminal.
SPEAKER TYPE
UNO G3
DUO G3
5
Only now connect the components' power cords to a household
MODEL NO.
ITRON AMP
ORIGIN
MADE IN GERMANY
outlet and turn on the subwoofer and other equipment.
only to be used with marked speaker type
+ 1.5
+ 1.5
0dB
ENGAGED
The inputs and outputs of the AMP SWITCH � are exclusively
�
FUSE
– 1.5
– 1.5
RESET
MID
HIGH
available on devices with ITRON amplifier (incl. the AMP SWITCH
E FUSE
DRIVER GAIN
circuitry) and are used for remote switching between PASSIVE cros‐
sover and ITRON amplifier.
17
1 5
HIGH
MID
MID
MID
SPEAKER TYPE
UNO G3
DUO G3
MODEL NO.
PASSIVE CROSSOVER SWITCH
only to be used with marked speaker type
ORIGIN
MADE IN GERMANY
WARNING
ELECTRICAL SHOCK HAZARD
PUSH
DO NOT OPEN!
110 – 240V ~ 50/60HZ
MAX POWER CONSUMPTION – 570W
POWER OUTPUT – 530W RMS
FUSE 2.5 A SLOW
+ 1.5
+ 3
+ 6
0dB
0dB
– 1.5
– 3
– 6
IN
OUT
BALANCED INPUT
TOTAL GAIN