KitchenAid 9750520 REV A Installation Instructions - Page 2

Browse online or download pdf Installation Instructions for Ranges KitchenAid 9750520 REV A. KitchenAid 9750520 REV A 5 pages. 30" electric freestanding range

Print Page

Important:

Observe all

governlng

codes and

ordinances.

Check location where range will be

installed. The range should be

located for convenient

use in kitchen.

ALL OPENINGS

IN THE WALL OR

FLOOR WHERE RANGE IS TO BE

INSTALLED MUST BE SEALED.

13" max.

upper

cabinet

+- depth

Before you start...

Proper installation

is your responsibility.

qualified technician should install this range.

Make sure you have everything necessary for

correct installation.

It is the responsibility

of the

installer to comply with installation clearances

specified on the serial/rating

plate. The

serial/rating plate is located on the oven frame

behind

the oven door.

~13"

max

upper

cabinet

depth

For minimum

clearance,

Personal

Injury Hazard

Avoid installing

cabinet storage above

the cooking

surface.

If cabinets

are

already Installed,

reduce the hazard of

reaching

over a heated cooking

surface

by Installing

a range hood. The range

hood should extend a minimum

of 5

inches out from the bottom front of the

cabinets.

Reaching

over a heated cooking

surface

could result in a serious

burn or other

personal

injury.

Electrical

Shock Hazard

It is the customer's

responsibility:

To contact

a qualified

electrical

installer.

To assure that the electrical

installation

Is adequate

and in conformance

with

National

Electrical

Code, ANSVNFPA

70-latest edition**,

and all local codes

and ordinances.

Failure to do so could result in fire,

electrical

shock or other personal

injury.

4" Min. . . see ":r-

counrenop

18" min. clearance

30-3/8"

upper cabinet

countertop.

openlng

wldth

Wall

receptacle

6" to 22" fron

elther cablne

7" max. from

floor.

o Not pinch

18 power

36"

countertop

helght

//-

///'

I ., '

Grounded

electricil\

cord between

the ran e and

outlet is reauired.

the wal ? .

Mobile home installation

The installation of this range must conform to

the Manufactured

Home Construction

and

Safety Standards, Title 24 CFR, Part 3280

(formerly the Federal Standard for Mobile

Home Construction

and Safety, Title 24, HUD,

Part 280); or when such standard is not

applicable, the Standard for Manufactured

Homes Installations

1982 (Manufactured

Home

Sites, Communities

and Setups), ANSI A2251 -

1987, or latest edition*', or with local codes.

When this range is installed in a mobile home,

it must be secured to the floor during transit.

Any method of securing the range is adequate

as long as it conforms to the standards listed

above.

See Electric'al

requirements.

\ \

/ I

Do Not seal

the range to

the slde

cabinets.

NOTE: Clearances

specified are for

combustible walls

and materials that have

-JY

a density of 20 or more

pounds per cubic foot. No

evaluation of clearances has

been made for installations

adjacent to materials that are

less than 20 pounds per cu. ft.

or to plastic tile or sheeting.

Cablnet opening

dimensions

that

are shown must be used. Given

dimensions

are minimum clearances

and provide required 0" clearance.

Four-wire power supply cable must be used in

a mobile home installation.

The appliance

wiring will need to be revised. See 4-wire

electrical connection,

Panel C.

Copies of the standards listed may be obtained

from:

**National

Fire Protection

Association

Batterymarch

Park

Quincy,

Massachusetts

02269

*Note: 24" mln. when bottom of wood

or metal cabinet

Is protected

by not

less than 114" flame retardant

mlllboard

covered

wlth not less than

No. 26 MSG sheet steel, 0.015"

stalnless

steel, 0.024" alumlnum

0.020" copper.

30" mln. clearance

between

the top

of the cooklng

platform

and the

bottom

of an unprotected

wood or

metal cabinet.

The an&tip

bracket

MUST

be Installed.

For

detalled

lnstructlons.

see Panels B

and C.

Tools needed for

Electrical

installation:

requirements

(A/

. A three-wire or a four-wire single phase,

120/240-volt, 60-Hz, AC-only, electrical

supply (or three-wire or four-wire 120/208-volt if

specified on serial plate) is required on a

separate 40-ampere circuit, fused on both sides

of the line. A time-delay fuse or circuit breaker is

recommended.

Save Installation Instructions

for the

local electrical inspector's use.

Power cord is not supplied but is

available through you local electrical

supply houses.

THE RANGE MUST BE CONNECTED

WITH COPPER WIRE ONLY.

/c.(

Electrlcal

Shock Hazard

. Electrical

ground

is required

on thls

appliance.

Improper

connection

of the equipment-

grounding

conductor

can result in

electrical

shock.

Check with a qualified

electrician

if you

are in doubt as to whether

the appliance

is properly

grounded.

Only a power supply

cord kit rated at 250

volts, 40 amperes and investigated

for

use with ranges should

be used.

Do Not have a fuse in the neutral or

grounding

circuit.

A fuse in the neutral or

grounding

circuit

could result in electrical

shock.

Do Not plug the "pigtail"

power cord into a

live wall receptacle

before the cord Is

permanently

connected

to the terminal

block. To do so may result in personal

injury from electrical

shock.

Failure to follow these instructions

could

result in a fire, electrical

shock or personal

injury.

Local codes may permit the use of a

U.L.-listed, 250-volt, 40-ampere range

power supply cord (pigtail). This cord' contains

three, No.-1 0 copper wires and matches a three-

wire receptacle of NEMA Type 1 O-50R, shown in

Figure 1. Connectors on the appliance end must

be ring terminals. A U.L.-listed strain relief must

be provided at the point the power supply cord

enters the appliance.

hand or electric

drill

wood/metal

wall stud:

l/B-Inch

drill blt

concrete/concrete

block walls:

3116.Inch carblde-tlpped

masonry

drill blt

ID.I

The appliance should be connected

directly to the fused disconnect or

circuit breaker box through flexible,

armored or non-metallic sheathed, copper

cable. Allow two or three feet of slack in the

line so that it can be moved if servicing is ever

necessary.

A U.L.-listed conduit connector must be

provided at each end of the power supply

cable (at the appliance and at the junction

box). Wire sizes (COPPER WIRE ONLY) and

connections

must conform with the rating of

the appliance (40 amperes).

Parts supplied

for

installation:

2 screws

(#lo x l-112")

(Thickness

of wall coverln

may

requlre

longer screws,

ava lable

from you local hardware

store.)

:ket

2 plastic

anchors

Panel A