KitchenAid YKESA907PP00 Installation Instructions Manual - Page 3
Browse online or download pdf Installation Instructions Manual for Ranges KitchenAid YKESA907PP00. KitchenAid YKESA907PP00 20 pages. 30"(76.2cm) freestanding and slide-in electric ranges
Print PageINSTALLATION REQUIREMENTS
Assemble the required tools and parts before starting installation.
Read and follow the safety instructions
provided with any tools
listed here.
Tools needed
•
Tape measure
•
3/8"drive rachet
•
Flat-blade screwdriver
•
1_,,nut driver
•
Level
•
8/18"nut driver
•
Hammer
•
1/8"(3.2 mm) drill bit (for
•
Hand or electric drill
wood floors)
•
Channel lock pliers
•
8/18"(4.8 mm) carbide-tipped
masonry drill bit (for
•
Marker or pencil
concrete/ceramic
floors)
•
Masking tape
Parts supplied
Check that all parts are included.
B
.......................
0
A. Anti-tip bracket
B. Plastic anchors (2)
C. #10x
_" screws (2)
D. Rear spacer cover for slide-in models
(supplied on some models)*
*To order, contact your dealer or refer to the "Assistance
or Service"
section of your Use and Care Guide. Ask for Part No. 9757784WH
(White), 9757784BT
(Biscuit), 9757784BL
(Black), 9757784MT
(Meteorite) or 9757784SS
(Stainless Steel).
Brackets must be securely mounted to subfloor. Thickness of
flooring may require longer screws to anchor bracket to
subfloor. Longer screws are available from your local
hardware store.
Parts needed
Check local codes. Check existing electrical supply. See
"Electrical Requirements"
section.
All electrical connections should be made by a licensed, qualified
electrical installer.
IMPORTANT: Observe all governing codes and ordinances.
Failure to meet codes and ordinances could lead to fire or
electrical shock.
•
It is the installer's responsibility to comply with installation
clearances specified on the model/serial rating plate. The
model/serial
rating plate is located on the oven frame behind
the storage drawer panel.
•
The range should be located for convenient use in the
kitchen.
To eliminate the risk of burns or fire by reaching over heated
surface units, cabinet storage space located above the
surface units should be avoided. If cabinet storage is to be
provided, the risk can be reduced by installing a range hood
that projects horizontally a minimum of 5" (12.7 cm) beyond
the bottom of the cabinets.
•
Cabinet opening dimensions that are shown must be used.
Given dimensions
are minimum clearances.
•
The floor anti-tip bracket must be installed. To install the
anti-tip bracket shipped with the range, see "Install Anti-Tip
Bracket" section.
•
Grounded electrical supply is required. See "Electrical
Requirements"
section.
Mobile Home - Additional
Installation
Requirements
The installation of this range must conform to the Manufactured
Home Construction
and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction
and Safety, Title 24, HUD Part 280). When such standard is not
applicable,
use the Standard for Manufactured
Home
Installations,
ANSI A225.1/NFPA 501A or with local codes.
In Canada, the installation of this range must conform with the
current standards CAN/CSA-A240-1atest
edition, or local codes.
Mobile home installations require:
•
When this range is installed in a mobile home, it must be
secured to the floor during transit. Any method of securing
the range is adequate as long as it conforms to the standards
listed above.
•
Four-wire power supply cord or cable must be used in a
mobile home installation. The appliance wiring will need to be
revised. See "Electrical Connection"
section.