Jandy Infinite WaterColors IWC15W100 Installation And Operation Manual - Page 8
Browse online or download pdf Installation And Operation Manual for Controller Jandy Infinite WaterColors IWC15W100. Jandy Infinite WaterColors IWC15W100 12 pages. Nicheless led light
Also for Jandy Infinite WaterColors IWC15W100: Manual (2 pages), Owner's Manual (16 pages)
Print Page
ENGLISH
Additionally, in the United States the National Electrical
Code
(NEC
) and in Canada the Canadian Electrical
®
®
Code (CEC), require that all metallic components of a pool
structure, including reinforcing steel, metal fittings and
above ground components be bonded together (forming an
equipotential bonding grid) with a solid copper conductor
not smaller than an 8 AWG (6 AWG in Canada).
The NEC and CEC also require that the equipment and/or
appliances associated with the pool water circulating
system, including, but not limited to, pump motors and
heaters, be bonded together as part of the equipotential
bonding grid. Zodiac Pool Systems LLC provides special
labeled bonding lugs on the bottom of the power center to
accommodate this requirement.
After bonding the electronics to the grounding lug,
installer must verify ground continuity of all metal
components using a multimeter.
Installer must ensure that the Infinite WaterColors
LED Light Controller is in acceptable working
condition; including all seals/gaskets must be
in place and functional; grounding lug must be
present, functional, and bonded; and corrosion must
not compromise ingress protection against weather.
Additionally, all hardware must be present and
functional. If any of the aforementioned conditions
are not met, a new enclosure MUST be used.
Risk of electric shock which can result in serious injury
or loss of life. Before attempting to install or service,
ensure that all power to the circuit supplying power to
the system is disconnected or turned off at the circuit
breaker. All wiring must be done in accordance with the
National Electrical Code
In Canada, the Canadian Electrical Code (CEC), CSA C22.1,
must be followed. All applicable local installation codes and
regulations must be followed.
Wiring connections must be made exactly as shown in
the wiring diagram found on the inside of the Infinite
WaterColors LED Light Controller cover. The NEC and
CEC also require that pool equipment be bonded together
as part of the equipotential bonding grid. Zodiac Pool
Systems LLC provides a labeled bonding lug on the bottom
of the Light Controller to accommodate this requirement.
Page 8
WARNING
WARNING
(NEC)
, NFPA-70
.
®
®
®
Jandy
Infinite WaterColors
LED Light Controller
®
™
Section 4. iAquaLink
Features
Download the iAquaLink app or upgrade to the latest
version prior to light and zone set up. App function and
design is subject to change.
NOTE: When replacing lights, make sure to follow
these steps:
•
Remove any existing light aux names
(system setup > label aux >)
•
Remove previous light aux labels
(system setup > color lights)
•
Remove schedules of light auxiliaries
(system setup > schedules)
4.1
Light Setup
1.
Open the app on your device.
2.
From My Systems page, select your pool.
3.
From the home page, choose the cog system icon
on the top right and select System Setup.
4.1.1
Assign Lights
1.
From the System Setup page, select Light Setup
and Assign Lights.
2.
From the Assign Lights pop up, choose proceed
to continue the process.
3.
On the Light Zone Setup page, select a light in
order to move it to a different zone and follow
further instructions in the app.
NOTE: When exiting the Light Zone Setup page, the lights will
turn off.
NOTE: Lights have to be assigned to a zone in order to
rename the zone.
4.1.2
Name Light Zones
1.
Go to > System Setup > Light Setup > Zone
Name.
2.
From the Edit Zone Name pop up, enter the zone
name and choose OK.
4.2
Turn Lights On/Off
1.
Open the app on your device.
2.
From My Systems page, select your pool.
3.
Choose the equipment page.
|
Installation & Operation Manual
App
®