Gardena 9811 Operator's Manual - Page 6

Browse online or download pdf Operator's Manual for Trimmer Gardena 9811. Gardena 9811 9 pages. Turbotrimmer
Also for Gardena 9811: Operating Instructions Manual (16 pages)

Print Page

• for Art. 9808 / 9809:

GARDENA Filament Cassette for Turbotrimmers

• for Art. 9811:

GARDENA Filament Cassette for Turbotrimmers

1. Press in cassette cover

on the two catches

remove.

2. Remove the filament cassette

3. Remove any dirt.

4. Pull approximately 15 cm of the cutting filament

f ilament cassette

through the hole in the plastic ring

5. First thread the cutting filament

6. For Art. 9808 / 9809 only: Thread the cutting filament

guide pin

7. Insert the filament cassette

8. Fit the cassette cover

on the filament cassette holder

you hear both locking clips

For Art. 9808 / 9809 only: When fitting the cassette cover

filament

must be placed around the guide pin

trapped.

v If the cassette cover

cannot be touched down, turn the filament

cassette

to and fro, until the filament cassette

the filament cassette holder

6. TROUBLESHOOTING

DANGER! Risk of injury from the cutting filament!

v Always unplug the mains plug of the Turbotrimmer

before troubleshooting!

Pulling the filament out of the filament cassette [ Fig. T1 ]:

If a filament is drawn into the filament cassette you can pull it out again as

described below.

1. Remove the filament cassette

"Replacing the filament cassette".

2. Press together the plastic ring

your thumb and forefinger.

3. Draw the plastic ring

over the side part of the filament cassette

(use a screwdriver if necessary).

You can now access the filament that was drawn into the filament

cassette.

4. Unwind the cutting filament

the eye of the plastic ring

. If necessary, loosen the welded filament

beforehand using a screwdriver, and unwind and rewind completely.

5. Pull the plastic ring

back over the filament cassette

6. Reinstall the filament cassette

"Replacing the filament cassette".

Problem

Possible Cause

The trimmer no longer cuts

Filament worn or too short.

The trimmer no longer cuts

Filament cassette empty.

Filament drawn into the

cassette or stuck together.

Filament cannot be

The filament became too dry

and brittle (e. g. over the winter).

extended or filament

is consumed rapidly

Frequent contact between the

filament and hard objects.

NOTE: For any other malfunctions please contact the GARDENA service depart-

ment. Repairs must only be done by GARDENA service departments or specialist

dealers approved by GARDENA.

7. TECHNICAL DATA

Turbotrimmer

Unit

Value (Art. 9808) Value (Art. 9809) Value (Art. 9811)

Motor power consumption

450

Mains voltage /

V / Hz

230 / 50 – 60

Mains frequency

Art. 5307

Art. 5309

at the same time and

out of the new

through the metal sleeve

around the

into the filament cassette holder

so that

click into place.

, the cutting

and must not be

is completely in

as described under 5. MAINTENANCE

on the filament cassette

between

by approx. 15 cm and thread it through

as described under 5. MAINTENANCE

Remedy

v Lengthen the filament

(see 3. OPERATION "Filament

feed – Tip mechanism" ) .

v Replace the filament cas sette

(see 5. MAINTENANCE

"Replac ing the filament

cassette") .

v Pull the filament out of the

filament cassette (see above).

v Place the filament in water

for approx. 10 hours.

v Avoid contact between the

filament and hard objects.

500

650

230 / 50 – 60

Turbotrimmer

Filament thickness

Cutting width

Filament supply

Filament feed

Rpm of filament cassette

(approx.)

Weight (approx.)

Telescopic adjustment of

the turn handle (approx.)

Sound pressure level L

Uncertainty k

Sound power level L

measured/guaranteed

Uncertainty k

Hand/arm vibration a

vhw

Uncertainty k

Measuring process complying with:

NOTE: The stated vibration emission value has been measured according to

a standardized test procedure and can be used for comparison of one electric

power tool with another. It can also be used for preliminary evaluation of

exposure. The vibration emission value can vary during actual use of the electric power

tool.

8. SERVICE / WARRANTY

Service:

Please contact the address on the back page.

Warranty:

In the event of a warranty claim, no charge is levied to you for the services

provided.

GARDENA Manufacturing GmbH offers a two-year warranty (effective

as of the date of purchase) for this product. This warranty includes all

significant defects of the product that can be proved to be material or

manufacturing faults. This warranty is fulfilled by supplying a fully functional

replacement product or by repairing the faulty product sent to us free of

charge; we reserve the right to choose between these options. This ser-

vice is subject to the following provisions:

• The product was used for its intended purpose as per the recommen-

dations in the operating instructions.

• Neither the purchaser nor a third party has attempted to repair the

product.

This manufacturer's warranty does not affect warranty entitlements against

the dealer / retailer.

If problems arise with this product, please contact our Service depart-

ment or send the defective product along with a brief description of the

fault to GARDENA Manufacturing GmbH, making sure to have sufficiently

covered any shipping costs and to have followed the relevant postage

and packaging guidelines. A warranty claim must be accompanied by

a copy of the proof of purchase.

Consumables:

The filament cassette and cassette cover are consumables and are not

covered by the guarantee.

Unit

Value (Art. 9808) Value (Art. 9809) Value (Art. 9811)

1.6

250

270

Tip mechanism

rpm

12,800

12,200

3.3

dB (A)

93 / 94

94 / 96

dB (A)

< 2.5

m/s

1.5

DIN EN 60335-2-91

RL2000/14/EG

DIN EN 786.

2.0

300

Tip mechanism

10,500 (Idle speed

approx. 9,500)

3.6

93 / 96

< 2.5

1.5