Gardena powerCut 2404 Operating Instructions Manual - Page 4
Browse online or download pdf Operating Instructions Manual for Trimmer Gardena powerCut 2404. Gardena powerCut 2404 8 pages. Turbotrimmer
Also for Gardena powerCut 2404: Operating Instructions Manual (12 pages)
Print Page
1. Leave the motor running.
2. Hold the cutting head
ground and tap the filament cassette
7
of the Turbotrimmer on the ground
several times in succession (approx.
3 times) (avoid applying sustained
pressure to the Turbotrimmer).
The filament is lengthened automatically.
Listen for the audible switching action.
E
The filament limiter
4. Maintenance
There is a risk of injury from the cutting filament !
Risk of injury !
V Always unplug the mains plug of the Turbotrimmer be-
fore carrying out maintenance work !
Risk of injury !
Risk of injury and risk of damage to property !
V Never clean the Turbotrimmer under running water or
with a water jet (in particular a high pressure water jet).
Cleaning the cover
The ventilation slots must always
be free of dirt.
and ventilation slots :
v Remove any grass and dirt from
the cover
after each use.
Replacing the filament
Risk of injury !
A
cassette :
V Never use metallic cutting elements or replacement
Only use original GARDENA Filament Cassettes. You can
I
order Replacement Filament Cassettes from your GARDENA
dealer or directly from the GARDENA Customer Service.
J
Filament Cassette for Turbotrimmer powerCut : Art. No. 5367-20
J
1. Unplug the mains plug.
2. Turn over the Turbotrimmer and rest it on the rubber buffer
of the handle.
E
3. Release the cassette cover
and remove the cover.
L
4. Remove the filament cassette
5. Remove any dirt.
K
6. Pull approximately 5 cm of the filament
filament cassette
N
7. Insert the filament cassette
so that the filament
8. Fit the cassette cover
that you hear both locking clips
M
When replacing the cover, ensure that the filament is inside the
metal case and is not trapped.
v If the cassette cover
filament cassette
is completely in the filament cassette holder
12
E
7
parallel to the
E
F
adjusts the filament to the correct length.
H
G
H
and ventilation slots
G
parts and accessories not provided by GARDENA.
I
by pressing both locking clips
E
.
K
out of the new
E
through the hole in the plastic ring
E
in the filament cassette holder
K
N
is inside the metal case
.
I
on the filament cassette holder
J
click into place.
I
cannot be touched down, turn the
E
to and fro, until the filament cassette
M
.
F
5. Trouble-Shooting
Risk of injury !
Pulling the filament
out of the filament cassette :
E
L
K
E
Fault
The Turbotrimmer
no longer cuts.
J
L
.
M
If you have any other problems please contact the GARDENA Customer Service.
M
so
6. Storage
E
Risk of injury from the cutting filament !
V Always unplug the mains plug of the Turbotrimmer be-
fore troubleshooting.
If a filament is drawn into the filament cassette you can pull it out
again as described below.
1. Unplug the mains plug.
2. Remove the filament cassette as described under 4. Mainte-
nance "Replacing the filament cassette" .
L
3. Press together the plastic ring
on the filament cassette
between your thumb and forefinger.
L
4. Draw the plastic ring
with the thumb of the other hand over
the side part of the filament cassette
if necessary).
You can now access the filament that was drawn into the fila-
ment cassette.
K
5. Unwind the filament
approximately 10 cm and thread
it through the eye of the plastic ring
cessary, loosen the filament beforehand
K
using a screwdriver. The filament
may stand out max. 2 cm over the
F
knife
.
L
6. Pull the plastic ring
back over the
E
filament cassette
.
7. Reinstall the filament cassette as described
L
under 4. Mainte-nance "Replacing the
filament cassette".
Only GARDENA Service Centres and authorised specialist
GARDENA dealers may carry out repairs.
Possible cause
Remedy
Filament worn or too short.
v Lengthen the filament –
see 3. Operation "Filament
feed (Tip mechanism for
automatic filament feed )".
Filament cassette empty.
v Replace the filament cassette
– see 4. Maintenance
"Replacing the filament
cassette" ).
Filament drawn into the
v Pull the filament out of the
cassette or stuck together.
filament cassette (see above).
The Turbotrimmer must be stored out of the reach of children.
v Store your Turbotrimmer in a dry place where it is protected
from frost.
E
E
(use a screwdriver
L
. If ne-
F
13