Gardena Accu 6 Operating Instructions Manual - Page 4

Browse online or download pdf Operating Instructions Manual for Lawn and Garden Equipment Gardena Accu 6. Gardena Accu 6 7 pages.

Print Page
G
When the cutting power drops, recharge your shears immedi-
ately to prevent the cells from becoming completely empty.
Warning !
There is a risk of injury if the switching devices installed
Risk of Injury
on the Shears are removed or bridged (e.g. by fastening
the on switch to the handle). This prevents the Edging Accu
Shears switching off automatically.
V Never remove or bridge the switching devices.
The starting lockout prevents your GARDENA Edging Accu Shears
from being switched on unintentionally.
Cutting Grass :
1. Clear the area to be cut of stones and other solid objects.
2. Push the starting lockout
3. Press the starting switch
4
5
4. Slide the Edging Accu Shears along the lawn on their sliding
sled or wheels
5
6
4
Cutting Grass with the
The length of the GARDENA Telescopic Swivel Handle (Art. No.
Telescopic Swivel Handle :
2525) can be infinitely varied and therefore adjusted to your indi-
vidual height. The swivel handle or the Edging Accu Shears can
be swivelled up to 45°.
17
1. Clear the area to be cut of stones and other solid objects.
18
2. Attach the Telescopic Swivel Handle (see "3. Assembly").
3. Loosen the adjusting bolt
20
4. Set the handle to the correct length and tighten the adjusting
J
bolt
5. Press and hold down the starting lockout
starting switch
6. Release the starting lockout
7. Slide the Edging Accu Shears along the grass on their sliding
sled or wheels

6. Maintenance

Blades can cause injury.
Warning !
Risk of Injury
V Disconnect your Edging Accu Shears from the mains
before carrying out maintenance work.
There is a risk of personal injury and damage to the Shears
Warning !
Personal Injury
if you clean them under running water (especially under
high pressure).
and Damage
to Property
V Never clean your Shears under running water.
14
4
forwards.
5
.
6
. This ensures a constant even cutting height.
J
.
.
G
and press the
H
. The blades begin to cut.
G
.
6
. This ensures a constant even cutting height.
Cleaning Your Edging Accu
To increase the cutting performance and lengthen their working
Shears and Oiling the Blades :
life, the Shears should be cleaned and oiled before and after use.
Never grease the blades.
1. Clean your Edging Accu Shears with a damp cloth.
2. Oil the blades (e.g. with sewing machine oil).
Cleaning the Blades
The blades of your GARDENA Edging Accu Shears are non-stick
thoroughly and
coated. To obtain good cutting results, the blades should be
Sharpening the Blades :
cleaned thoroughly from time to time and should always be sharp.
Always remove notches and burrs caused by stones etc. imme-
diately.
1. Remove the blades (see "7. Trouble-shooting ", "Replacing
9 8
Grass Cutting Blades" ).
2. Separate the upper blade
3. Remove any grass and dirt between the upper and lower
blades.
4. Sharpen the blades using a sharpening stone.
5. Fit the blades (see "7. Trouble-shooting ", "Replacing Grass
Cutting Blades" ).
7. Trouble-shooting
Warning !
Blades can cause serious injury.
Risk of Injury
V Disconnect the Edging Accu Shears from the mains
before trouble-shooting.
Fault
Possible cause
Edging Accu Shears
Blades are faulty.
do not cut well
Please only use original GARDENA Edging Accu Shears Trimmer
Replacing Grass Cutting
Blades :
Blades:
• Art. No. 2345 for Accu 3 / Accu 4
• Art. No. 2346 for Accu 6
1. Loosen screws
9 8 7 14
2. Clean the area around the gears and lubricate the gear wheels
with non-corrosive grease (Vaseline).
3. Turn the cam gear
12
exactly forwards.
4. Ensure the upper blade
of the lower blade
10
5. Guide the blade underneath the blade pegs
Make sure the cam
11
6. Tighten the screws
13
G
8
9
and lower blade
.
Remedy
v Check blades and replace
if necessary.
7
and remove grass cutting blades.
0
A
so that the marking line
is pointing
8
is positioned exactly in the middle
9
.
B
of the carriage.
C
D
snaps into the connecting link
.
7
.
15