Gardena AquaContour automatic 1559 Operator's Manual - Page 5
Browse online or download pdf Operator's Manual for Lawn and Garden Equipment Gardena AquaContour automatic 1559. Gardena AquaContour automatic 1559 12 pages. Large-area pop-up irrigation
Also for Gardena AquaContour automatic 1559: Operating Instructions Manual (13 pages), Operator's Manual (13 pages)
Print Page
the change in direction matches the required irrigation
limits. If watering in a complete circle, the two sector
(L)
ß
stops
and
must be completely pushed together
R
between P1 and P10.
Anti-vandal device:
If the nozzle head is violently turned over the sector-stops
then the vandalism protection is triggered. As soon as the
water supply is open, the sprinkler moves in one direction
until the set sector has been achieved again.
Programme contour points of irrigation sector
[ Fig. O2 / F1 / O3 ]:
The watering sector has to be selected before program-
ming. Up to 50 contour points can be programmed with
the largearea pop-up irrigation. The more points that
are programmed, the more precisely the contour will be
described (e. g. with a circular arc P7 – P10).
q
1. Open the two locks
2. Open water supply.
When using for the first time, the minimum range
(2.5 m with a flow pressure of 2 bar at the sprinkler)
is selected.
3. Press OK button
4
.
6
The green Auto LED
4. Press Menu button
1
5
The red Set LED
lights up.
0
5. Turn the nozzle head
to the left-hand sector limit (in the example P1) and
hold.
6. Use the two buttons "+" button
to set the range so that it reaches P1.
7. Press OK button
4
.
The green Auto LED
6
first point P1 has been stored.
8. Turn the nozzle head
0
to the next irrigation point (e. g. P2) and hold.
9. Use the two buttons "+" button
to set the range so that it reaches P2 for example.
5. MAINTENANCE
Clean dirt filter [ Fig. M1 ]:
1. Open both locks
q
and raise the cover
e
2. Turn the dirt filter
anticlockwise 1 and pull out
carefully 2 (bayonet coupling).
e
3. Clean dirt filter
under clean running water.
e
4. Refit dirt filter
in reverse order.
w
5. Close cover
and both locks
Clean nozzles [ Fig. M2 / M3 ]:
If the watering pattern is no longer even, the nozzles can
be cleaned using the cleaning needle provided.
q
1. Open both locks
and raise the cover
2. Turn the cleaning needle
clockwise through 180° 1 and pull out carefully 2
(bayonet coupling).
12
w
and raise the cover
.
lights up.
.
on the orange ring by hand
2
and "–" button
lights up for 1 second and the
on the orange ring by hand
2
and "–" button
w
.
q
.
w
.
r
(e. g. with a coin) anti-
10. Press OK button
The green Auto LED
point has been stored.
11. Repeat the process from step 8 to 10 until the right-
hand sector limit is reached (in the example P10).
12. Press Menu button
The red Set LED
complete, and the green Auto LED
1 minute. The red Set LED then flashes every
8 seconds.
13. Release nozzle head
watered.
14. If the contour is watered correctly, close the water
supply.
w
15. Close cover
Information about programming:
As soon as the first point is programmed, any existing
programme will be deleted. After programming has been
completed, no further points can be deleted or added
later on. If the contour has not been set as required,
reprogramming with more points will have to be carried
out. If no button is pressed for 60 seconds during pro-
gramming, programming will be automatically ended and
the contour stored.
Start / end watering:
Before irrigation can be started, the large-area
pop-up irrigation must have been programmed.
Start watering:
v Fully open water supply.
3
Watering will start automatically and the contour of the
watering sector previously programmed will be watered.
End watering:
v Close water supply.
Watering will end. The programme remains unchanged.
If no irrigation or programming is being made, the sprinkler
3
goes into "sleep mode" (the green Auto-LED
light up and the red Set-LED blinks every 8 seconds).
t
3. Clean nozzles
4. Refit cleaning needle
w
5. Close cover
and both locks
Clean protective panel of solar cell:
To make sure that the rechargeable battery is always
sufficiently charged, the protective panel of the solar cell
has to be cleaned if soiled.
No caustic / abrasive cleaning agents or hard objects
should be used.
v Clean protective panel of solar cell with a damp cloth.
4
.
6
lights up for 1 second and the
1
.
5
goes out, programming is
6
lights up for
0
and check contour area
q
and both locks
.
6
r
with cleaning needle
.
r
in reverse order.
q
.
does not