Garmin FENIX 5S PLUS Owner's Manual - Page 17

Browse online or download pdf Owner's Manual for Watch Garmin FENIX 5S PLUS. Garmin FENIX 5S PLUS 25 pages.

Print Page

If necessary, attach the strap extender to the heart rate

monitor.

Wet the electrodes

on the back of the heart rate monitor to

create a strong connection between your chest and the

transmitter.

Wear the heart rate monitor with the Garmin logo facing right-

side up.

The loop

and hook

side.

Wrap the heart rate monitor around your chest, and connect

the strap hook to the loop.

NOTE: Make sure the care tag does not fold over.

After you put on the heart rate monitor, it is active and sending

data.

Tips for Erratic Heart Rate Data

If the heart rate data is erratic or does not appear, you can try

these tips.

• Reapply water to the electrodes and contact patches (if

applicable).

• Tighten the strap on your chest.

• Warm up for 5 to 10 minutes.

• Follow the care instructions

Monitor, page

11).

• Wear a cotton shirt or thoroughly wet both sides of the strap.

Synthetic fabrics that rub or flap against the heart rate

monitor can create static electricity that interferes with heart

rate signals.

• Move away from sources that can interfere with your heart

rate monitor.

Sources of interference may include strong electromagnetic

fields, some 2.4 GHz wireless sensors, high-voltage power

lines, electric motors, ovens, microwave ovens, 2.4 GHz

cordless phones, and wireless LAN access points.

Caring for the Heart Rate Monitor

A buildup of sweat and salt on the strap can decrease the ability

of the heart rate monitor to report accurate data.

• Rinse the heart rate monitor after every use.

• Hand wash the heart rate monitor after every seven uses or

one pool swim, using a tiny amount of mild detergent, such

as dishwashing liquid.

NOTE: Using too much detergent may damage the heart rate

monitor.

Color Gauges and Running Dynamics Data

The running dynamics screens display a color gauge for the primary metric. You can display cadence, vertical oscillation, ground

contact time, ground contact time balance, or vertical ratio as the primary metric. The color gauge shows you how your running

dynamics data compare to those of other runners. The color zones are based on percentiles.

Heart Rate Features

connection should be on your right

(Caring for the Heart Rate

NOTICE

• Do not put the heart rate monitor in a washing machine or

dryer.

• When drying the heart rate monitor, hang it up or lay it flat.

Running Dynamics

You can use your compatible fēnix device paired with the

HRM-Run

™

accessory or other running dynamics accessory to

provide real-time feedback about your running form. If your fēnix

device was packaged with the HRM-Run accessory, the devices

are already paired.

The running dynamics accessory has an accelerometer that

measures torso movement in order to calculate six running

metrics.

Cadence: Cadence is the number of steps per minute. It

displays the total steps (right and left combined).

Vertical oscillation: Vertical oscillation is your bounce while

running. It displays the vertical motion of your torso,

measured in centimeters.

Ground contact time: Ground contact time is the amount of

time in each step that you spend on the ground while

running. It is measured in milliseconds.

NOTE: Ground contact time and balance are not available

while walking.

Ground contact time balance: Ground contact time balance

displays the left/right balance of your ground contact time

while running. It displays a percentage. For example, 53.2

with an arrow pointing left or right.

Stride length: Stride length is the length of your stride from one

footfall to the next. It is measured in meters.

Vertical ratio: Vertical ratio is the ratio of vertical oscillation to

stride length. It displays a percentage. A lower number

typically indicates better running form.

Training with Running Dynamics

Before you can view running dynamics, you must put on a

running dynamics accessory, such as the HRM-Run accessory,

and pair it with your device

page

31). If your fēnix 5/5S/5X Plus was packaged with the

accessory, the devices are already paired, and the fēnix 5/5S/5X

Plus is set to display running dynamics data screens.

Select an option:

• If your running dynamics accessory and fēnix 5/5S/5X

Plus device are already paired, skip to step 7.

• If your running dynamics accessory and fēnix 5/5S/5X

Plus device are not already paired, complete all the steps

in this procedure.

Hold MENU.

Select Settings > Activities & Apps.

Select an activity.

Select the activity settings.

Select Data Screens > Add New.

Select a running dynamics data screen.

NOTE: The running dynamics screens are not available for

all activities.

Go for a run

(Starting an Activity, page

Select UP or DOWN to open a running dynamics screen to

view your metrics.

(Pairing Your Wireless Sensors,

2).