Garmin echomap 50 series Owner's Manual - Page 12

Browse online or download pdf Owner's Manual for Marine GPS System Garmin echomap 50 series. Garmin echomap 50 series 50 pages. Flat-mount kit
Also for Garmin echomap 50 series: Quick Start Manual (4 pages), Owner's Manual (38 pages), Owner's Manual (44 pages), Owner's Manual (30 pages), Installation Instructions Manual (6 pages), Installation Instructions Manual (6 pages), Installation Instructions Manual (34 pages)

Garmin echomap 50 series Owner's Manual
• Select Photo Map Blend to show photos on both the
water and the land at a specified opacity. Use the slider
bar to adjust the photo opacity. The higher you set the
percentage, the more the satellite photos cover both land
and water.

Viewing Aerial Photos of Landmarks

Before you can view aerial photos on the Navigation chart, you
must turn on the Satellite Photos setting in the chart setup.
NOTE: This feature is available with premium charts, in some
areas.
You can use aerial photographs of landmarks, marinas, and
harbors to help orient yourself to your surroundings or to
acquaint yourself with a marina or a harbor prior to arrival.
1
From the Navigation chart, select a camera icon:
• To view an overhead photo, select
• To view a perspective photo, select
taken from the location of the camera, pointed in the
direction of the cone.
2
Select Aerial Photo.
Garmin Quickdraw
The Garmin Quickdraw Contours mapping feature allows you to
instantly create maps with contours and depth labels for any
body of water.
When Garmin Quickdraw Contours records data, a colored
circle surrounds the vessel icon. This circle represents the
approximate area of the map that is scanned by each pass. A
green circle indicates good depth and a good GPS position. A
red circle indicates that the depth or GPS position data is
unavailable.
You can view Garmin Quickdraw Contours in a combination
screen or as a single view on the map.
The amount of saved data depends on the size of your memory
card, your sonar source, and the speed of your boat as you
record data. You can record longer when you use a single-beam
sonar. It is estimated that you might be able to record about
1,500 hours of data onto a 2 GB memory card.
When you record data on a memory card in your chartplotter,
the new data is added to your existing Garmin Quickdraw
Contours map, and is saved on the memory card. When you
insert a new memory card, the existing data does not transfer
onto the new card.
Mapping a Body of Water Using the Garmin
Quickdraw Contours Feature
Before you can use the Garmin Quickdraw Contours feature,
you must have a supported chartplotter with upgraded software,
sonar depth, your GPS position, and a memory card with free
space.
NOTE: This feature is not available on all models.
1
From a chart view, select Menu > Quickdraw Contours >
Start Recording.
2
When recording is complete, select Stop Recording.
3
Select Manage > Name, and enter a name for the map.
Adding a Label to a Garmin Quickdraw Contours Map
You can add labels to a Garmin Quickdraw Contours map to
mark hazards or points of interest.
1
From the Navigation chart, select a location.
2
Select Add Quickdraw Label.
3
Enter text for the label, and select Done.
Garmin Quickdraw Contours Settings
From the chart, select Menu > Quickdraw Contours >
Settings.
6
.
. The photo was
Contours Mapping
Recording Offset: Sets the distance between the sonar depth
and the contour recording depth. For example, a sonar depth
of 3.6 m (12 ft.) with a recording offset of -0.5 m (-1.5 ft.)
creates contours at a depth of 3.1 m (10.5 ft.).
Display Offset: Sets differences in contour depths and depth
labels on a Garmin Quickdraw Contours map to compensate
for changes in the water level of a body of water, or for depth
errors in recorded maps.
Survey Coloring: Sets the color of the Garmin Quickdraw
Contours display. When the setting is turned on, successfully
recorded areas appear green, and unsuccessfully recorded
areas appear red. When the setting is turned off, the contour
areas use standard map colors.
Automatic Identification System
The Automatic Identification System (AIS) enables you to
identify and track other vessels, and alerts you to area traffic.
When connected to an external AIS device, the chartplotter can
show some AIS information about other vessels that are within
range, that are equipped with a transponder, and that are
actively transmitting AIS information.
The information reported for each vessel includes the Maritime
Mobile Service Identity (MMSI), location, GPS speed, GPS
heading, time that has elapsed since the last position of the
vessel was reported, nearest approach, and time to the nearest
approach.
Some chartplotter models also support Blue Force Tracking.
Vessels being tracked with Blue Force Tracking are indicated on
the chartplotter with a blue-green color.
AIS Targeting Symbols
Symbol Description
AIS vessel. The vessel is reporting AIS information. The
direction in which the triangle is pointing indicates the
direction in which the AIS vessel is moving.
Target is selected.
Target is activated. The target appears larger on the chart. A
green line attached to the target indicates the heading of the
target. The MMSI, speed, and direction of the vessel appear
beneath the target, if the details setting has been set to Show.
If the AIS transmission from the vessel is lost, a message
banner appears.
Target is lost. A green X indicates that the AIS transmission
from the vessel is lost, and the chartplotter displays a
message banner asking whether the vessel should continue
to be tracked. If you discontinue vessel tracking, the lost
target symbol disappears from the chart or the 3D chart view.
Dangerous target in range. The target flashes while an alarm
sounds and a message banner appears. After the alarm has
been acknowledged, a solid red triangle with a red line
attached to it indicates the location and the heading of the
target. If the safe-zone collision alarm has been set to Off, the
target flashes, but the audible alarm does not sound and the
alarm banner does not appear. If the AIS transmission from
the vessel is lost, a message banner appears.
Dangerous target is lost. A red X indicates that the AIS
transmission from the vessel is lost, and the chartplotter
displays a message banner asking whether the vessel should
continue to be tracked. If you discontinue vessel tracking, the
lost dangerous target symbol disappears from the chart or the
3D chart view.
The location of this symbol indicates the closest point of
approach to a dangerous target, and the numbers near the
symbol indicate the time to the closest point of approach to
that target.
NOTE: Vessels being tracked with the Blue Force Tracking
feature are indicated with a blue-green color regardless of their
status.
Charts and 3D Chart Views