Garmin ECHOMAP PLUS 60 series Owner's Manual - Page 36

Browse online or download pdf Owner's Manual for Marine GPS System Garmin ECHOMAP PLUS 60 series. Garmin ECHOMAP PLUS 60 series 50 pages.
Also for Garmin ECHOMAP PLUS 60 series: Installation Instructions Manual (6 pages), Quick Start Manual (8 pages), Installation Instructions Manual (6 pages)

Print Page

Garmin ECHOMAP PLUS 60 series Owner's Manual

Select an option:

• After you have filled up all the fuel tanks on the vessel,

select Fill Up All Tanks. The fuel level is reset to

maximum capacity.

• After you have added less than a full tank of fuel, select

Add Fuel to Boat, and enter the amount added.

• To specify the total fuel in the vessel tanks, select Set

Total Fuel Onboard, and enter the total amount of fuel in

the tanks.

Viewing the Wind Gauges

Before you can view wind information, you must have a wind

sensor connected to the chartplotter.

Select Gauges > Wind.

Configuring the Sailing Wind Gauge

You can configure the sailing wind gauge to show true or

apparent wind speed and angle.

From the wind gauge, select MENU > Sailing Wind Gauge.

Select an option:

• To show true or apparent wind angle, select Needle, and

select an option.

• To show true or apparent wind speed, select Wind Speed,

and select an option.

Configuring the Speed Source

You can specify whether the vessel speed data displayed on the

gauge and used for wind calculations is based on water speed

or GPS speed.

From the wind gauge, select MENU > Compass Gauge >

Speed Display.

Select an option:

• To calculate the vessel speed based on data from the

water-speed sensor, select Water Speed.

• To calculate the vessel speed based on GPS data, select

GPS Speed.

Configuring the Heading Source of the Wind Gauge

You can specify the source of the heading displayed on the wind

gauge. Magnetic heading is the heading data received from a

heading sensor, and GPS heading is calculated by your

chartplotter GPS (course over ground).

From the wind gauge, select MENU > Compass Gauge >

Heading Source.

Select GPS Hdg or Magnetic.

NOTE: When moving at low speeds or when stationary, the

magnetic compass source is more accurate than the GPS

source.

Customizing the Close-Hauled Wind Gauge

You can specify the range of the close-hauled wind gauge for

both the upwind scale and the downwind scale.

From the wind gauge, select MENU > Compass Gauge >

Set Gauge Type > Close Hauled Gauge.

Select an option:

• To set the maximum and minimum values that appear

when the upwind close-hauled wind gauge appears, select

Change Upwind Scale, and set the angles.

• To set the maximum and minimum values that appear

when the downwind close-hauled wind gauge appears,

select Change Downwind Scale, and set the angles.

• To view true or apparent wind, select Wind, and select an

option.

Tide, Current, and Celestial

Information

Tide Station Information

You can view information about a tide station for a specific date

and time, including the tide height, and when the next high and

low tides will occur. By default, the chartplotter shows tide

information for the most recently viewed tide station, present

date, and past hour.

Select Nav Info > Tides & Currents > Tides.

Current Station Information

NOTE: Current station information is available with certain

detailed maps.

You can view information about a current station for a specific

date and time, including the current speed and level of the

current. By default, the chartplotter shows current information for

the most recently viewed current station and for the present date

and time.

Select Nav Info > Tides & Currents > Currents.

Celestial Information

You can view information about sunrise, sunset, moonrise,

moonset, moon phase, and the approximate sky view location of

the sun and moon. The center of the screen represents the sky

overhead, and the outermost rings represent the horizon. By

default, the chartplotter shows celestial information for the

present date and time.

Select Nav Info > Tides & Currents > Celestial.

Viewing Tide Station, Current Station, or

Celestial Information for a Different Date

Select Nav Info > Tides & Currents.

Select Tides, Currents, or Celestial.

Select an option:

• To view information for a different date, select Change

Date > Manual, and enter a date.

• To view information for today, select Change Date > Use

Current Date.

• If available, to view information for the day after the date

shown, select Next Day.

• If available, to view information for the day before the date

shown, select Previous Day.

Viewing Information for a Different Tide or

Current Station

Select Nav Info > Tides & Currents.

Select Tides or Currents.

Select Nearby Stations.

Select a station.

Digital Selective Calling

Chartplotter and NMEA 0183 VHF Radio

Functionality

When your chartplotter is connected to a NMEA 0183 VHF

radio, these features are enabled.

• The chartplotter can transfer your GPS position to your radio.

If your radio is capable, GPS position information is

transmitted with DSC calls.

• The chartplotter can receive digital selective calling (DSC)

distress and position information from the radio.

Tide, Current, and Celestial Information