Garmin GPSMAP 751 Installation Instructions Manual

Browse online or download pdf Installation Instructions Manual for Marine GPS System Garmin GPSMAP 751. Garmin GPSMAP 751 8 pages.
Also for Garmin GPSMAP 751: Quick Start Manual (4 pages), Owner's Manual (38 pages)

Print Page

GPSMAP

500/700 Series and

echoMAP™ 50/70 Series Installation

Instructions

Important Safety Information

See the Important Safety and Product Information guide in the

product box for product warnings and other important

information.

When connecting the power cable, do not remove the in-line

fuse holder. To prevent the possibility of injury or product

damage caused by fire or overheating, the appropriate fuse

must be in place as indicated in the product specifications. In

addition, connecting the power cable without the appropriate

fuse in place will void the product warranty.

Always wear safety goggles, ear protection, and a dust mask

when drilling, cutting, or sanding.

When drilling or cutting, always check what is on the opposite

side of the surface.

Registering Your Device

Help us better support you by completing our online registration

today.

• Go to http://my.garmin.com.

• Keep the original sales receipt, or a photocopy, in a safe

place.

Contacting Garmin Product Support

• Go to

www.garmin.com/support

for in-country support information.

• In the USA, call (913) 397.8200 or (800) 800.1020.

• In the UK, call 0808 2380000.

• In Europe, call +44 (0) 870.8501241.

Tools Needed

• Drill and drill bits

• #2 Phillips screwdriver

• Marine sealant

• Jigsaw

• File and sandpaper

Mounting Considerations

This device should be mounted in a location that is not exposed

to extreme temperatures or conditions. The temperature range

for this device is listed in the product specifications. Extended

exposure to temperatures exceeding the specified temperature

range, in storage or operating conditions, may cause device

failure. Extreme-temperature-induced damage and related

consequences are not covered by the warranty.

Using the included hardware and template, you can mount the

device using one of two methods. You can use the included

bracket and hardware to bail mount the device, or you can use

the included template and hardware to flush mount the device in

February 2013

WARNING

CAUTION

NOTICE

and click Contact Support

NOTICE

the dashboard. If you want to mount the device using an

alternative method where it appears flat with the front of the

dashboard, you must purchase a flat-mount kit (sold separately,

with professional installation recommended) from your Garmin

dealer.

When selecting a mounting location, observe these

considerations.

NOTE: Not all mounting methods are available for all device

models. See the specific mounting-type section for more details

about your model.

• The location should provide optimal viewing as you operate

your boat.

• The location should allow for easy access to all device

interfaces, such as the keypad, touchscreen, and card

reader, if applicable.

• The location must be strong enough to support the weight of

the device and protect it from excessive vibration or shock.

• To avoid interference with a magnetic compass, the device

should not be installed closer to a compass than the

compass-safe distance value listed in the product

specifications.

• The location must allow room for the routing and connection

of all cables.

Bail Mounting a Five-Inch Device

If you are mounting the bracket on fiberglass with screws, it is

recommended to use a countersink bit to drill a clearance

counterbore through only the top gel-coat layer. This will help to

avoid any cracking in the gel-coat layer when the screws are

tightened.

Stainless-steel screws may bind when screwed into fiberglass

and overtightened. Garmin recommends applying an anti-

galling, stainless anti-seize lubricant to the screws before

installing them.

You can use the included bracket to bail mount the device on a

flat surface. The five-inch models have the option of installing a

swivel at the base of the bail-mount bracket

Using the bail-mount bracket

holes

Using a

in. (3 mm) drill bit, drill the pilot holes.

Using the included screws

to the mounting surface.

Install the bail-mount knobs

Place the device in the bail-mount bracket and tighten the

bail-mount knobs.

190-01556-02_0A

NOTICE

(page

2).

as a template, mark the pilot

, secure the bail-mount bracket

on the sides of the device.

Printed in Taiwan