Garmin GPS 19x NMEA 0183 Installation Instructions Manual - Page 2
Browse online or download pdf Installation Instructions Manual for Marine Equipment Garmin GPS 19x NMEA 0183. Garmin GPS 19x NMEA 0183 6 pages. Gps 19x hvs
Also for Garmin GPS 19x NMEA 0183: Installation Instructions Manual (8 pages), Installation Instructions Manual (48 pages), Installation Instructions Manual (6 pages), Installation Instructions Manual (19 pages)
Print Page
Before you permanently mount the antenna, you must test the
mounting location for correct operation
Location, page
1).
1
Using the surface-mount bracket
template, mark the three pilot-hole locations and trace the
cable-hole in the center of the bracket.
2
Set the surface-mount bracket aside.
Do not drill through the bracket.
1
3
Drill the three 3.2 mm (
4
Drill the 25 mm (1 in.) cable hole in the center.
5
Use the included M4 screws to secure the surface-mount
bracket to the mounting surface.
6
Route the cable
through the center hole, and connect it to
the antenna.
7
Verify the large gasket
antenna, place the antenna on the surface-mount bracket,
and twist it clockwise to lock it in place.
8
Secure the antenna to the mounting bracket with the included
M3 screw
.
9
Route the cable away from sources of electronic interference.
Mounting the Antenna on a Pole
Mounting the Antenna with the Cable Routed Outside the
Pole
Before you permanently mount the antenna, you must test the
mounting location for correct operation
Location, page
1).
1
Route the cable through the pole-mount adapter
place the cable in the vertical slot
pole-mount adapter.
2
Screw the pole-mount adapter onto a standard 1 in. OD, 14
threads per inch, pipe-threaded pole (not included).
Do not overtighten the adapter on the pole.
3
Connect the cable to the antenna.
2
(Testing the Mounting
as your mounting
/
in.) pilot holes.
8
is in place on the bottom of the
(Testing the Mounting
along the base of the
4
Place the antenna on the pole-mount adapter and twist it
clockwise to lock it in place.
5
Secure the antenna to the adapter with the included M3 set
screw
.
6
With the antenna installed on the pole mount, fill the
remaining gap in the vertical cable slot with a marine sealant
(optional).
7
Attach the pole to the boat if it is not already attached.
8
Route the cable away from sources of electronic interference.
Mounting the Antenna with the Cable Routed Through the
Pole
Before you permanently mount the antenna, you must test the
mounting location for correct operation
Location, page
1
Position a standard 1 in. OD, 14 threads per inch, pipe-
threaded pole (not included) in the selected location, and
mark the approximate center of the pole.
2
Drill a hole using a 19 mm (
pass through.
3
Fasten the pole to the boat.
4
Thread the pole-mount adapter onto the pole.
Do not overtighten the adapter.
5
Route the cable through the pole and connect it to the
antenna.
6
Place the antenna on the pole-mount adapter and twist it
clockwise to lock it in place.
7
Secure the antenna to the adapter with the included M3 set
screw
.
, and
8
With the antenna installed on the pole mount, fill the vertical
cable slot
9
Route the cable away from sources of electronic interference.
Mounting the Antenna Under a Surface
Verify that the supplied screws will not penetrate the surface
before you install the under-deck mounting bracket. If the
supplied screws are too long, use surface-appropriate screws
instead.
Because the antenna cannot acquire signals through metal, it
must be mounted under a fiberglass surface only.
1
Determine and test the location under a fiberglass surface
where you want to mount the antenna
Location, page
(Testing the Mounting
1).
3
/
in.) drill bit for the cable to
4
with a marine sealant (optional).
NOTICE
1).
(Testing the Mounting