Garmin GPSMAP 7012 Installation Instructions Manual - Page 3
Browse online or download pdf Installation Instructions Manual for Marine Equipment Garmin GPSMAP 7012. Garmin GPSMAP 7012 21 pages. Weather and xm satellite radio gpsmap 4000 series; gpsmap 5000 series; gpsmap 6000 series; gpsmap 7000 series
Also for Garmin GPSMAP 7012: Owner's Manual (2 pages), Technical Reference (42 pages), Important Safety Information (48 pages), Declaration Of Conformity (6 pages), Template Manual (2 pages), Supplement Manual (24 pages)
Print Page
Flush Mounting the GPSMAP 6000/7000 Series Chartplotter
Hardware (included):
• Flush-mount template
• Rubber gasket
• Four flush-mount nut-plates
• Four 60 mm M3 × 0.5 screws (to secure the nut plate to the
mounting surface)
• Four M4 × 0.7 screws (to secure the chartplotter to the nut plate)
• Four 7 mm nylon washers (for the M4 × 0.7 screws)
1. The flush-mount template is included in the product box. Trim the template and ensure that it will fit in the location at which you want to flush
mount the chartplotter.
NotES:
• Ensure that the surface on which you mount the chartplotter has enough open space behind it to accommodate the chartplotter and the
connected wires. Refer to the diagram on the flush-mount template for the clearance-space needed by your chartplotter.
• Ensure that there is at least
flush-mount template.
• Ensure that enough ventilation is present behind the mounting surface to create sufficient air flow to prevent the chartplotter from
overheating.
• To avoid interference, mount GPSMAP 6008/6208 chartplotters 15 in. (38.1 cm), GPSMAP 6012/6212 chartplotters 16 in. (40.6 cm),
GPSMAP 7012/7212 chartplotters 25 in. (63.5 cm) and 7015/7215 chartplotters 17 in. (43.2 cm) from a magnetic compass.
2. The flush-mount template has adhesive on the back. Remove the protective liner and apply the template to the location at which you want to
flush mount the chartplotter.
3. Using a
/
in. (9.5 mm) drill bit, drill one or more of the four pilot holes inside the corner of the template to begin cutting the mounting
3
8
surface.
4. Using a jigsaw, cut the mounting surface along the inside of the solid line indicated on the flush-mount template. Use a file and sandpaper to
refine the size of the hole. Be very careful when cutting this hole. there is only a small amount of clearance between the case and
the mounting holes.
5. Place the chartplotter in the hole and ensure that the mounting holes on the chartplotter line up with the larger
flush-mount template after cutting, sanding, and filing the hole. If they do not line up, mark new locations for the larger holes.
6. Using a center punch, indent the center of each of the larger
7. Using a
/
in. (7.2 mm) drill bit, drill the four larger holes.
9
32
8. Starting in one corner of the template, place a nut plate over the larger hole you drilled in step
7. Ensure that the smaller
on the template. If they do not line up, mark a new location for the smaller hole. Repeat this
step for each corner of the template.
9. Using a center punch, indent the center of each of the smaller
locations.
10. R emove the flush-mount template from the mounting surface.
11. S tarting in one corner of the mounting location, place a nut plate on the back of the mounting
surface, lining up the large and small holes. The raised portion of the nut plate should fit into
the larger hole.
12. S ecure the nut plate to the mounting surface by fastening an included 60 mm M3 × 0.5 screw
through the smaller
/
in. (3.5 mm) hole.
9
64
GPSMAP 6000/7000 Series Installation Instructions
/
in. (13 mm) of space on the right side of the chartplotter to access the SD card door, as indicated on the
1
2
/
in. (3.5 mm) hole on the nut plate lines up with the smaller hole
9
64
tools required (not included):
• Jigsaw
• Scissors
• Drill
• Drill bits—
/
in. (9.5 mm),
3
8
• Number 2 Phillips screwdriver
• Center punch and hammer
• File and sandpaper
/
in. (7.2 mm) mounting-hole locations.
9
32
/
in. (3.5 mm) mounting-hole
9
64
/
in. (7.2 mm), and
/
in. (3.5 mm)
9
9
32
64
/
in. (7.2 mm) holes on the
9
32
Use the 60 mm M3 × 0.5 screw
to fasten the nut plate to the
mounting surface
Use the 70 mm M4 × 0.7 screw
to fasten the chartplotter to the
nut plate
Flush-mount Nut Plate
3