Garmin Delta Upland Owner's Manual - Page 7
Browse online or download pdf Owner's Manual for Pet Care Product Garmin Delta Upland. Garmin Delta Upland 14 pages. Instructions
Also for Garmin Delta Upland: Instructions (4 pages)
Print Page
Beeper Sounds
The beeper device can emit two sounds: a beep and a hawk scream. These sounds indicate your dog's hunting and pointing status.
While your dog is hunting, the beeper device emits a series of one to three beeps every four seconds. You can select the number of
beeps in the series, which is useful to distinguish between multiple dogs. You can also disable this sound so that the beeper device
is silent while your dog is hunting.
When your dog is pointing, the beeper emits either one beep every second or one hawk scream every five seconds, depending on
the setting you choose.
When you select beeper sounds, the selected sounds are indicated briefly by the status LEDs. The red status LED indicates the
hunting sound, and the green status LED indicates the pointing sound.
Mode Red LED Hunting Sound Green LED Pointing Sound
1
1 blink
1 beep
2
2 blinks
2 beeps
3
3 blinks
3 beeps
4
Off
Silent
5
1 blink
1 beep
6
2 blinks
2 beeps
7
3 blinks
3 beeps
8
Off
Silent
Customizing the Beeper Sounds
1
With the device turned on, hold the power key until both
LEDs blink rapidly three times, and release the power key.
2
Select the power key to cycle through the sound modes.
Each time you select the power key, the LEDs indicate the
selected sound mode. You may have to cycle through
several sound modes to reach your preferred sound mode.
3
Hold the power key until both LEDs blink rapidly three times,
and release the power key to set the sound mode to the
current selection.
Resetting to the Default Beeper Sounds
You can reset your beeper device to the factory default sound
settings, regardless of the current setting or power state of the
device.
Hold the power key for 15 seconds.
The device emits a high-low, high-low beep sequence, and
the LEDs flash to confirm the reset.
The next time you turn on the device, it is set to mode 1.
Introducing Your Dog to the Beeper Device
The beeper device is loud and may startle an inexperienced
dog. You should introduce your dog to the device before you
use it during a hunt. You can use any of these methods to help
your dog adjust to the sounds.
• Place a piece of duct tape over the speaker opening to
muffle the sounds during your first use of the device on the
dog.
• Turn on the device, and place it near your dog's kennel for
several hours.
This allows the dog to hear and adjust to the sounds in a
comfortable location.
Turning the Beeper Sounds On or Off
Remotely
Before you can turn the beeper sounds on or off remotely, the
dog collar device and the beeper device must be turned on.
You can use the handheld device to turn the beeper sounds on
or off remotely. Turning off the beeper sounds does not turn off
the beeper device.
1
On the handheld device, select a training mode in which a
training key is assigned to the beeper device.
Dog Training
Solid
Hawk scream
Blinking
Beep
2
Select the training key assigned to the beeper device to turn
the beeper sounds on or off for the selected dog.
Locating Your Dog Using the Beeper Device
You can remotely trigger the beeper device to emit a series of
beeps, which you can use to determine the location of your dog.
1
On the handheld device, select the dog to locate
Dog Collar
Device).
2
Select a training mode in which a training key is assigned to
B
(Selecting a Training
3
Hold the training key assigned to B.
The beeper device emits a series of beeps for as long as you
hold the training key, up to eight seconds.
Dog Training
You should research and investigate the training methods best
suited for you, your dog, and your needs. This manual provides
some basic guidelines for training, but each dog has unique
training needs.
When used properly, the Delta Upland training system is a very
effective training tool to aid your dog in reaching its full potential.
The use of the training system should be part of an overall
training program.
Begin training your dog on a leash, without the Delta Upland
training system. You should train your dog how to heel, sit, and
come to you. After the dog understands these three basic
commands, you can begin training with the dog collar device
and the leash. Finally, when the dog consistently obeys
commands using the leash and collar, you may be able to
remove the leash to train with only the dog collar device.
Fitting the Collar on Your Dog
To prevent irritation from the contact points, remove the collar
for at least eight hours out of every 24-hour period.
This device is not intended for human use. Do not attempt to
use on any person.
Before you put the collar on the dog, remove the charging clip. If
you do not remove the clip, it may become detached from the
collar and become lost.
(Selecting a
Mode).
CAUTION
NOTICE
3