Garmin PRO Control 2 HH Owner's Manual - Page 8

Browse online or download pdf Owner's Manual for Pet Care Product Garmin PRO Control 2 HH. Garmin PRO Control 2 HH 12 pages.
Also for Garmin PRO Control 2 HH: Owner's Manual (12 pages)

Print Page

1. Charging the Handheld Device

Mode Top Key

Middle Key

TVM Tone

Vibration

VCM Vibration

Continuous

(high)

TCM Tone

Continuous

(high)

CMM Continuous

Momentary

(high)

MCC Momentary

Continuous

(high)

Selecting a Training Mode

You can select a different training mode for each dog collar

device.

Select a dog collar device

Select RAPID LAUNCH to toggle through the available

training modes.

Choosing the Correct Intensity Level

Set the intensity to the lowest level

Level).

Press a training key.

Observe the dog for a reaction, such as a head shake, neck

movement, or just a change in expression.

Sometimes dogs will vocalize due to the surprise of the

electrical stimulation. If the dog vocalizes more than once,

the intensity level is too high for beginning training.

If there is no reaction, increase the intensity level by one level

until the dog has a slight but recognizable reaction to the

stimulation.

The intensity level that causes a slight but recognizable reaction

is your dog's baseline level for beginning collar training. You do

not need to, and should not, apply this intensity selection test

again.

After you begin training, the dog's performance guides your

intensity selection. As the dog advances in training, you may

need to change the level depending upon the training situation.

Changing the Intensity Level

You can select a different intensity level for each dog collar

device.

Select a dog collar device

Select

to increase or decrease the intensity level.

The numerical intensity level appears on the LCD display.

TIP: You can hold

quickly.

Device Information

PRO Control 2 Handheld Device

Specifications

Battery type

Operating temperature range

Charging temperature range

Storage temperature range

Water rating

*The device withstands incidental exposure to water of up to 1 m

for up to 30 min. For more information, go to

/waterrating.

Bottom Key

Description

Momentary

Beginning trainer,

(low)

sensitive dog, or

minor corrections

Momentary

All-around training

(high)

Momentary

All-around training

(high)

Momentary

Advanced

(low)

training, popular

for bird-dog

training

Continuous

Advanced

(low)

training, popular

for obedience

training

(Selecting a Dog Collar

Device).

(Changing the Intensity

(Selecting a Dog Collar

Device).

to cycle through intensity levels

Rechargeable, replaceable lithium-ion

From -4° to 158°F (from -20° to 70°C)

From 32° to 104°F (from 0° to 40°C)

From -4° to 122°F (from -20° to 50°C)

IEC 60529 IPX7*

www.garmin.com

PRO Control 2 Battery Replacement

Instructions

This product contains a lithium-ion battery. To prevent the

possibility of personal injury or product damage caused by

battery exposure to extreme heat, store the device out of direct

sunlight.

Do not use a sharp object to remove batteries.

Contact your local waste disposal department to properly

recycle the batteries.

PRO Control 2 Handheld Device Components

Security screws

Back plate

Battery

Battery connector

Gasket

Replacing the PRO Control 2 Handheld Device Battery

Before you replace the battery, you must remove all dirt, water,

and debris from the device. You also need the security

screwdriver included with the new battery.

You can purchase a replacement battery at

http://buy.garmin.com. You should use only an official Garmin

replacement part.

Remove the six security screws from the back of the device.

Lift up the back plate.

Grip the battery connector wires close to the connector, and

pull the connector parallel to the circuit board to disconnect

the battery connector from the device.

Remove the old battery from the back plate, noting the

orientation of the battery.

The battery fits tightly. It may be necessary to pry the battery

out of the back plate using a non-sharp, non-metal object.

Install the new battery into the back plate with the label side

up, using the same orientation as the old battery.

With the new battery, connect the battery connector to the

device.

When properly installed, the connector plug snaps into the

port.

Verify the gasket is not damaged and is completely seated in

the groove.

Hold the back plate and the device firmly together, and

replace all six security screws without tightening.

Verify the back plate and the device are aligned with no gaps.

Tighten the screws evenly.

WARNING

CAUTION

Device Information