Fujitsu Lifebook A3040 Bios Manual - Page 2
Browse online or download pdf Bios Manual for Laptop Fujitsu Lifebook A3040. Fujitsu Lifebook A3040 24 pages. Bios setup utility
Also for Fujitsu Lifebook A3040: Software Manual (29 pages)
Print Page
L i f e B o o k A S e r i e s N o t e b o o k B I O S
A Series BIOS
BIOS SETUP UTILITY
The BIOS Setup Utility is a program that sets up the
operating environment for your notebook. Your BIOS
is set at the factory for normal operating conditions,
therefore there is no need to set or change the BIOS
environment to operate your notebook.
The BIOS Setup Utility configures:
Device control feature parameters, such as changing
■
I/O addresses and boot devices.
System Data Security feature parameters, such as
■
passwords.
Entering the BIOS Setup Utility
To enter the BIOS Setup Utility do the following:
1. Turn on or restart your notebook.
2. Press the [F2] key once the Fujitsu logo appears on
the screen. This will open the main menu of the
BIOS Setup Utility with the current settings
displayed.
3. Press the arrow keys to scroll through the other
setup menus to review or alter the current settings.
Navigating Through The Setup Utility
The BIOS setup utility consists of six menus: Main,
Advanced, Security, Boot, Info, and Exit. This document
explains each menu in turn, including all submenus and
setup items.
The following procedures allow you to navigate the
setup utility menus:
1. To select a menu, use the cursor keys:
2. To select a field within a menu or a submenu, use the
cursor keys:
[ ], [ ].
3. To select the different values for each field, press the
[Spacebar] or [+] to change to the next higher
selection and [-] to go to the next lower selection.
4. To activate a submenu press the [Enter] key.
5. To return to a menu from a submenu, press
the [Esc] key.
6. To go to the Exit menu from any other menu,
press the [Esc] key.
2
7. Pressing the [F9] key resets all items in the BIOS to
8. Pressing the [F10] key saves the current configura-
9. Pressing the [F1] key gives you a general help screen.
Entering the Setup Utility After a Configuration
Change or System Failure
If there has been a change in system configuration that
does not agree with the parameter settings stored in your
BIOS memory, or there is a failure in the system, the
system beeps and/or displays an error message after the
Power On Self Test (POST). If the failure is not severe, it
will give you the opportunity to modify the settings of
the setup utility, as described in the following steps:
1. When you turn on or restart the computer there is a
2. If an error message is displayed on the screen, and
[
], [
].
Selecting a field causes a help message
■
about that field to be displayed on the
right-hand side of the screen.
■
Pressing the Enter key with the highlight
on a selection that is not a submenu or
auto selection will cause a list of all
options for that item to be displayed.
Pressing the Enter key again will select
the highlighted choice.
the default values.
tion and exits the BIOS Setup Utility. You will be
asked to verify this selection before it is executed.
beep and/or the following message appears on the
screen:
Error message - please run SETUP
program Press <F1> key to continue,
<F2> to run SETUP
you want to continue with the boot process and start
the operating system anyway, press the [F1] key.
■
If your notebook emits a series of beeps
that sounds like a code and the display is
blank, refer to the Troubleshooting sec-
tion of your system Use's Guide. The
Troubleshooting Section includes a list of
error messages and their meanings.
■
If your data security settings require it,
you may be asked for a password before
the operating system will be opened.