2N EasyGate IP Quick Manual - Page 2

Browse online or download pdf Quick Manual for Gateway 2N EasyGate IP. 2N EasyGate IP 2 pages.

Print Page

Connector Layout and Meanings

FXS

Analog line

NO (Normally Open), contact that is open against the COM contact at relax.

RELAY

COM, contact that switches between NO and NC after voltage is applied to the coil.

NC (Normally Closed), contact that is connected with the COM contact at relax.

INPUT

Short-circuit input. Not used for voltage connection.

Used for connecting the device with the serial bus (in some controller types, e.g.).

TX, transmission wire interface.

RS232

RX, receiving wire.

GND, grounding.

A short press restarts the device. A long press (10 s) resets the device factory

RESET

values.

USB

Used for local access to the 2N® EasyGate IP settings via a Web configuration utility.

SIM 1

Primary SIM card slot without PIN.

SMA

Antenna connector.

SIM 2

Secondary SIM card slot for primary SIM card backup in the case of signal loss.

POWER Power supply connector.

EXT

Connector for remote connection of 4 NiMH batteries outside the device. Make sure

BATT

that the internal batteries are removed before connecting external batteries.

O/I

Device on/off switch.

Mechanical Installation

2N® EasyGate IP is designed for indoor mounting on a vertical surface using a DIN rail holder or on a

wall using screws fitted to the holder mounting holes. The installed device is intended for permanent

operation at the minimum separation distance of 20 cm from the user.

Wall mounting

Use the holder and two dowels with screws included in the package to install 2N® EasyGate IP on a wall.

Drill holes in a selected place and selected height of the wall and insert the dowels. Pass the screws

through the holder holes and screw them into the dowels in the wall. Now all you have to do is slide

2N® EasyGate IP from the top into the holder profile.

DIN rail mounting

No other tool is needed for DIN rail installation. The DIN rail holder has a standard size of 35 mm. Put

the upper inner side of the holder profile on the DIN rail and push its bottom side to make the holder

click and fit to the DIN rail. Now all you have to do is slide 2N® EasyGate IP from the top into the DIN

rail holder profile. Now all you have to do is insert 2N® EasyGate IP in the holder profile from the top

downwards and fit the gateway position with a screw.

!!! Only vertical mounting with the connectors heading down guarantees that the device will

be waterproof. If installed otherwise, the device may be infiltrated with water and damaged

irreversibly !!!

With the supplied batteries, the device may be operated in the range of 0 °C – 45 °C.

Outside this range, the device may not be operated with the supplied batteries. Remember to

use batteries with increased thermal resistance in order to make the backup function work.

You can connect an external battery with increased thermal resistance or use an external

battery placed under convenient temperature conditions.

Putting in Operation

Device Connection to Power

Connect the included power supply terminal block

into the dedicated Power connector and connect

the power supply to the electrical mains.

SIM Card Installation

Insert a SIM card without PIN request into the SIM 1 slot on the device bottom side. Remember to set

PIN deactivation and such provider services as call forwarding, call barring, preferred networks, SMS

center, etc., in your mobile phone, for example, before inserting the SIM card in 2N® EasyGate IP.

2N® Elevator Center, a licensed cloud service, is used for remote management of 2N® EasyGate IP. Ask

your distributor to create the service access data for you. Refer to 2n.cz for details on the 2N® Elevator

Center service.

To configure 2N® EasyGate IP without the 2N® Elevator Center cloud service connect the device to a PC

via a USB cable and use 2N® EasyGate IP – Web configuration utility, which can be downloaded for free

from 2n.cz. The 2N® Easygate IP local connection tool also includes a manual that described the tool

installation and leads the user as far as the web interface login page. Enter Admin as the user name and

2n as the password for the first login. Having been logged in to the web interface, you will be invited to

change the default password.

Refer to the 2N® EasyGate IP full manual at wiki.2n.cz for device configuration details.

Antenna Connection

Screw the enclosed antenna into the SMA antenna

connector. Tighten the antenna connector gently

with your hand, never use a wrench!