Brother PT-P900W Quick Setup Manual - Page 2
Browse online or download pdf Quick Setup Manual for Label Maker Brother PT-P900W. Brother PT-P900W 9 pages.
Print Page
Connecting the Power Supply
AC Adapter
Use the AD9100ESA (AC adapter) for this P-touch Label Printer. Connect the
AC adapter directly to the P-touch Label Printer.
1.
Insert the plug on the AC adapter cord into the AC adapter socket
marked DC IN 24 V on the P-touch Label Printer.
2.
Insert the plug on the power supply cord into the AC adapter.
1
AC adapter
2
Power supply cord
3.
Insert the power supply plug into a standard AC power outlet.
IMPORTANT
•
Turn the P-touch Label Printer off before disconnecting the AC
adapter.
•
Do not pull or bend the AC adapter cord and power supply cord.
•
After the power supply plug is inserted into the AC power outlet, it
may take a few seconds until the
NOTE
To safeguard and backup the P-touch Label Printer memory, when the
power supply is unplugged it is recommended to have the rechargeable
battery (optional: PA-BT-4000LI) installed in the P-touch Label Printer.
Using the Rechargeable Li-ion Battery
(Optional)
Attach the battery base (PA-BB-002) to the P-touch Label Printer. For more
information about attaching the battery base, see its instruction manual.
Installing the Rechargeable Li-ion Battery
1.
Press and hold the
(Power) button to turn the P-touch Label Printer
off.
2.
Open the battery cover on the bottom of the P-touch Label Printer.
3.
Insert the battery into the battery compartment.
4.
Close the battery cover.
Removing the Rechargeable Li-ion Battery
Press and hold the
(Power) button to turn the P-touch Label Printer off.
Remove the battery cover and the battery, and then reattach the battery
cover.
1
2
(Power) button is enabled.
Charging the Rechargeable Li-ion Battery
NOTE
•
Before use, fully charge the battery.
•
Up to three hours may be needed to fully charge the battery.
1.
Make sure the battery is installed in the P-touch Label Printer.
2.
Use the AC adapter and power supply cord to connect the P-touch
Label Printer to an AC power outlet.
Press the
(Power) button to turn the P-touch Label Printer on if it is
not on already.
The
(Battery) indicator lights in orange during charging, and it goes
off when the battery is fully charged.
1
AC adapter
2
Power supply cord
NOTE
Although the charging stops if the P-touch Label Printer is used to print,
feed, or perform another operation, the charging will start again
automatically after the operation is finished if the charging is not
completed.
Stopping Rechargeable Li-ion Battery Charging
To stop the battery charging, disconnect the AC adapter.
Notes on Using the Rechargeable Li-ion Battery
Before use, fully charge the battery. Do not use it until it is fully charged.
The battery charging must take place in environments between 0°C and
40°C, otherwise the battery will not charge, and the
indicator will remain lit. If the charging stops because the environment
temperature is too low or too high, place the P-touch Label Printer with
a temperature between 0°C and 40°C and try charging again.
If the P-touch Label Printer is used to print, feed, or perform another
operation when both the battery is installed and the AC adapter is
connected, the
(Battery) indicator may turn off and charging may
stop even if the battery is not fully charged.
Rechargeable Li-ion Battery Characteristics
To ensure the highest performance and longest life from the battery:
Do not use or store the battery in a location exposed to extreme high or
low temperatures as it may discharge more quickly. This may happen
when using a rechargeable Li-ion battery with a high charge (90%
charged or more) in a location exposed to high temperatures.
Remove the battery when storing the P-touch Label Printer for long
periods of time.
Store a battery with less than a 50% charge in a cool dry place out of
direct sunlight.
Recharge the battery every six months if it is stored for long periods of
time.
If you touch a part of the P-touch Label Printer while the Li-ion battery is
charging, that part of the P-touch Label Printer may feel warm. This is
normal, and the P-touch Label Printer may be used safely. However, if
the P-touch Label Printer becomes extremely hot, discontinue use.
1
2
(Battery)