Indesit Arcadia Sevice Manual - Page 2

Browse online or download pdf Sevice Manual for Washer Indesit Arcadia. Indesit Arcadia 3 pages. Fault codes

Print Page

FAULT

Pressure switch empty condition not

F05

reached (valid for linear and status pres-

sure switch) or drain pump jammed (valid

for linear and status pressure switch)

Door lock fails to close/open, door lock

PTC triac open/closed, mains frequency

F06

signal fault, mains power signal fault

Wash heating element relay open/diverter

F07

relay sticking on drain pump side

Wash heating element relay earth leak-

F08

age/wash heating element relay contacts

sticking

Setting File error detected by Main PCB

F09

or Display PCB

Pump not wired or pump driving triac

F11

short circuit

Communication error between Main PCB

F12

and Display PCB

2/3

Arcadia Fault Codes (Simple)

CAUSE

- If status type pressure switch, check component directly;

- Check efﬁ ciency of connector contacts on PCB;

- Check pressure switch wiring;

- Check continuity of pump on connector pins 4 and 5 (in case

- Check the wiring of pins 4 and 5(/pump;

- Check pump ﬁ lter, drain hose and wall drain outlet;

- Replace the drain pump;

- Replace the linear pressure switch;

- Replace the main PCB.

- Check for water leaks that may affect connectors J004 (collector)

- Check the door lock terminal board (possible problems due to

- Check J004/door lock wiring;

- Replace door lock;

- Replace PCB.

- Check efﬁ ciency of contacts on connector J001(commutator) or

- Check continuity of wash heating element on connectors

- Renew PCB.

- Check efﬁ ciency of contacts on connector J001(commutator) or

- Check leakage between the two ends and ground, impedance

- Renew heating element;

- Renew PCB.

- Disconnect appliance for 2 minutes. Check that correct operation

- Reprogram Main PCB;

- Renew main PCB;

- Renew display PCB.

- Check efﬁ ciency of contacts on connector J004 (commutator)

- Check continuity on connector J004 (commutator) or J11 (three-

- Check continuity of pump, ensuring that impedance value is 170

- Check wiring of connector J004 (commutator) or J11 (three-

- Renew pump;

- Renew PCB.

- Check efﬁ ciency of contacts on connector J010 (Commutator)

- Check efﬁ ciency of contacts on Display PCB;

- Check continuity of J010 (Commutator) or J16 (Three-phase)/

- Disconnect appliance, wait for 2 minutes and reconnect to power

If problem persists proceed as follows:

- Renew main PCB;

- Renew display PCB.

SERVICE ACTIONS

of classic door lock), ensuring that impedance value is 170 Ω

+/- 10%;

Reset the appliance with the OFF button, also after Fault resetting

with plug. Check the appliance pressure switches reaches full

without Faults at the next cycle;

or J11 (three-phase) causing the relative contacts to short;

aggression caused by manufacturing chemical residues that

may cause short circuits);

J10 (three-phase) on PCB;

J001(Commutator) or J10 (Three-phase), pins 3 and 4. The

1700W 230V heating element impedance value is 30 Ohm

+/- 10%. If value is different renew wash heating element;

J10 (three-phase) on PCB;

should be at least 2 MOhm;

has been restored by starting the Autotest routine;

or J11 (three-phase) on PCB;

phase), pins 4 and 5 (in the case of classic door lock);

Ohm +/- 10%;

phase)/pump;

or J16 (Three-phase) on main PCB;

Display PCB wiring;

supply, then start autotest routine;