Indesit WIXXE 14 Instructions For Use Manual - Page 19
Browse online or download pdf Instructions For Use Manual for Washer Indesit WIXXE 14. Indesit WIXXE 14 24 pages.
Print Page
Personalisations
FUNCTION buttons
this phase, the "delay" can only be modified by decreasing it.
The Delay Timer regulation is enabled with all programmes.
Setting the temperature
If, when the appliance is switched on, the KNOB is positioned on a programme for which the temperature needs
to be regulated, a fixed
will be displayed and the
indicates a cold wash cycle (press it again to go back to the maximum value); stop on the desired value, after
approximately 2 seconds the setting is accepted: the symbol
The temperature adjustment is enabled with all wash programmes.
Functions
To enable a function:
1. press the button corresponding to the desired function, according to the table below;
2. the function is enabled when the corresponding button is illuminated.
Note: The rapid flashing of the button indicates that the corresponding function cannot be selected for the
programme set.
If you set a function that is incompatible with another function you selected previously, only the last one selected
will be enabled.
Fu nc tion
E ffe c t
B leach in g cycle
d es ig n ed t o
S t a i n
rem o ve th e
r e m o v a l
t o u g h es t s t ain s .
I n creas es t h e
efficien cy o f th e
rin s e.
E x t r a
R i n s e
T h is o p tio n
red u ces th e
am o u n t o f
E a s y i r o n
creas in g o n
fab rics , m ak in g
t h em eas ier t o
iro n .
Setting the spin cycle
If, when the appliance is switched on, the KNOB is positioned on
a programme with a spin cycle, a fixed
and the maximum spin speed allowed for the programme set
will be displayed, and the
values lower until they reach OFF, which indicates that the spin
cycle has been excluded (press it again to go back to the
maximum value); stop on the desired speed, after approximately
2 seconds the setting is accepted: the symbol
The spin cycle setting is enabled with all the programmes except
for 6 and the Draining cycle.
Setting the delay timer
Press the button
display, while the relative symbol flashes.
Press the button again and "1h" appears, that is, a delay of one
hour (this can reach up to 24h); stop on the "desired" delay; after
approximately 2 seconds the setting is accepted, following which,
the time for the set programme appears on the display and the
symbol
If you now press the START/RESET button, the set "delay"
appears; this decreases every hour until the start of the cycle. In
appears. Press button
and the maximum temperature allowed for the programme set
icon flashes. Press it again and the temperature lowers until it reaches OFF, which
C om m e n ts
P leas e rem em ber t o p o u r th e b leach in t o ex t ra co m p art m en t 4
(s ee pag e 2 0 ).
T h is fu n ct io n is in co m p at ib le w it h th e EA S Y I R O N fu n ct io n .
R eco m m en d ed w h en th e ap plian ce h as a fu ll lo ad o r w it h larg e
qu an t it ies o f det erg en t .
W h en t h is fu n ctio n is s et , p ro g ram m es 4 an d 6 w ill en d , w it h th e
lau n d ry left t o s o ak (A n t i- creas e), an d t h e relat ive bu t t o n flas h es :
- t o co n clu de t h e cycle, p res s t h e S TA R T /R ES ET b u tt o n o r t h e
EA S Y I R O N bu t t o n ;
- t o ru n t h e d rain in g cycle alo n e, s et th e k n o b t o t h e relat ive
s ym b o l
an d p res s t h e S TA R T /R ES ET b u t to n .
T h is fu n ct io n is in co m p at ib le w it h th e S TA I N R EM O VA L fu n ctio n .
icon flashes. Press it again and the
and you will see the word OFF on the
remains on.
remains fixed.
GB
appears. Press button
remains fixed.
Ena b le d with
p r ogr a m m e s:
2 , 3 , 4 ,
R in se c yc le .
1 , 2 , 3 , 4 , 7 ,
8 , 9 , 1 1 , 1 2 ,
R in se c yc le .
3, 4, 6, 7, 8, 9,
R in se c yc le .
19