Indesit FIMD E23 IX Instructions For Installation And Use Manual - Page 33

Browse online or download pdf Instructions For Installation And Use Manual for Oven Indesit FIMD E23 IX. Indesit FIMD E23 IX 40 pages. Electric built-in double oven
Also for Indesit FIMD E23 IX: Instructions For Installation And Use Manual (40 pages)

Print Page

Installation

Electrical Requirements

For your own safety, we recommend that your cooker

is installed by a competent person such as one who

is registered with NICEIC (National Inspection

Council for Electrical Installation Contracting). The

cooker should be installed in accordance with the

latest edition of the IEE Regulations.

Warning: This appliance must be earthed.

Electrical Connections

The installer must check that the voltage shown on

the rating plate corresponds with the house

electricity supply. The cooker must be supplied via

a suitable double pole isolating switch, having a

contact separation of at least 3mm in all poles

placed in a readily accessible position adjacent to

the cooker. If the cooker is to be wired into a

connector unit, this may be positioned behind the

cooker providing the following requirements are met:

i) The connector unit must not project from the wall

more than 25mm.

ii) The top of the connector must not be more than

130mm above floor level.

Remove the terminal cover at the rear base of the

cooker. Pass the cable through the cable clamp and

connect to the appropriate terminals provided.

Allow sufficient cable for any future servicing.

Tighten the screws on the cable clamp and replace

the cover. Make main connections in the connector

unit or cooker control unit. This appliance conforms

to B.S. EN 55014 regarding suppression of Radio

and Television reception interference.

A double Pole control switch having a minimum

rating of 32 amps should be used to feed the cooker

using a suitably rated cable. Where a hob is fitted

adjacent to or over the cooker, a 45 amp Double

Pole control switch should be used to feed both

units via separate suitably rated cables.

We recommend a minimum of 4mm2 PVC insulated

twin and earth cable conforming to B.S. 6004 for

connection of each appliance.

In all cases adhere to routing details (see fig. 4).

This appliance must not be installed over any other

appliance that generates heat such as a plinth

heater.

Note: Due to many different types of installation,

a mains cable is not supplied with this product.

The installer will fit the correct type and length of

cable.

Important

It is essential that the lower cupboard is constructed in

the manner illustrated i.e. having side, back, and roof

panels so joined as to provide no apertures which

could permit access to the oven unit when installed.

1. General

The appliance is designed for mounting at a safe

level into an oven housing which must be secured to

the backing wall.

2. Ventilation

a. The oven housing unit cabinet dimensions must

comply with fig. 4.

b. An air gap of 50mm minimum must be provided at

the rear of any top or bottom cupboards or shelves

(see fig. 1).

c. It is necessary that the cabinets are provided with

unobstructed ventilation, i.e. from adjacent

cabinetry. This can be done by either raising the

base of the cabinets using the adjusting feet (or

spacers) or alternatively by providing a slot in the

cabinet plinth to the dimensions in fig. 1.

d. The air gap at rear allows the warmed air to pass out

of the inner cabinet space. Where it is intended to fit

cupboards above the oven unit to ceiling height, it is

essential that the warmed air is exhausted through

the front of the cabinet (see fig. 1).

e. If an oven unit is installed adjacent to a tall cabinet,

steam escaping from the oven when the door is

opened could condense on and maybe stain the

adjacent surface. To prevent permanent staining, the

adjacent surface should be made of a material that is

heat resisting and easy to clean. Adjacent tall cabinets

should not be deeper than the oven housing cabinet.

3. Final Installation

a. Using a spirit level, check that the housing cabinet

is level from side to side and from front to back in

its installed position.

b. Correct any unevenness by placing spacers under

the bottom of the cabinet. Make sure that the cabinet

rests firmly on the floor without rocking.

c. Before the oven is fitted, the cabinet must be firmly

secured to the backing wall for stability.

d. The oven unit should now be lifted (this is a two

person lift) into the cabinet and pushed fully home.

e. Finally, the oven is secured to the cabinet by means

of the four Phillips C/SK Head screws - two through

each side trim.

f. Remove all packaging material from the grill and

oven interior.

List of loose items:

4 x Phillips C/SK Head No. 6 x 25mm screws.