Indesit WD 84 T Instruction - Page 14

Browse online or download pdf Instruction for Washer/Dryer Indesit WD 84 T. Indesit WD 84 T 18 pages.

Print Page

Installation and removal

When the new washer-

dryer arrives

Whether new or just transported to a new house,

installation is extremely important for the correct

functioning of your washer-dryer.

After removing the appliance from

its packaging, check that it is

intact. If in doubt, contact a

qualified technician immediately.

The inside of the machine is

supported, for transportation, by

four screws on the back panel.

Before using the washer-dryer,

remove the screws, remove the

spacers together with the rubber

tubes attached to them (keeping

all the parts) and use the plastic

plugs provided to fill in the holes.

Important: Use the cap (provided)

to close the 3 holes which housed

the stop pin, situated in the right-hand

part of the lower back of the

washer-dryer.

Levelling

The washer-dryer must be levelled

appropriatey in order to guarantee

its correct functioning. To level the

appliance, the front feet must be

adjusted; the angle of inclination,

measured according to the worktop,

must not exceed 2°. When placed

on carpet, make sure the ventilation

is not reduced.

Retain the transit screws,

spacers and washers.

Should you move house

then these should be

replaced to support the

inside of the machine to

prevent damage when

transporting the machine.

Connection to the water

mains

Water pressure must range within

the values indicated on the data

plate on the rear of your washer-

dryer. If the water pipes are new or

left unused, then before connecting

the machine run the water until clear

to remove debris. Connect the inlet

hose to a cold water tap having a

¾ " BSP thread. Ensure that the

rubber sealing washer-dryers are

fitted at each end of the inlet hose,

with the fitter washer-dryer at the

tap end.

Connect the inlet hose to the

threaded connector on the

machine rear.

Connecting the drain hose

There are two hooks (right or left)

on the rear of your washer-dryer

to which the drain hose is to be

fixed. Insert the other end in a

stand pipe or place it on the edge

of a sink or tub avoiding excessive

kinks and bending. It should be

placed at a height ranging from 60

to 100 cm. If it is necessary to fix

the end of the hose at a height

below 60 cm from the ground, it

must be fixed in the appropriate

hook placed on the upper part of

the back panel.

If the drains hose empties into a

tub or sink then fit the plastic gui-

de and secure it to the tap.

The end of the drain hose must

be positioned so that it cannot

become submerged.

Extensions are unadvisable. In

case of absolute need, the

extension must have the same

diameter as the original hose and

must not exceed 150 cm. In case

of wall draining pipes, their

efficiency must be checked by

a qualified technician. If the

dwelling is on one of the upper

floors of a building, there may be

drain trap problems causing the

washer-dryer to load and unload

water continuously.

In order to avoid such an

inconvenience, special anti-drain

trap valves are available in

shops.

Electric connection

Before connecting the appliance

to the electric socket, be sure that:

1) the electric socket is able to

sustain the appliance's

maximum

power

load

indicated on the data plate

and in compliance with the

law;

2) the supply voltage is included

within the values indicated on

the data plate;

3) the socket is compatible with

the appliance's plug. If not, do

not use adapters, but replace

either the socket or the plug;

4) electric household appliances

must be equipped with an

"earthing" system.

Warning!

The company denies all

liability if and when these

norms are not respected.

Plastic bags, expanded

styrofoam, nails and other

packaging parts are not

children's toys, and are

potentially dangerous.