Indesit F105539 Instruction Manual - Page 2

Browse online or download pdf Instruction Manual for Dryer Indesit F105539. Indesit F105539 16 pages.

Print Page

1. Programmes and Options

Installation

Where to install the tumble dryer

If the dryer is installed below a worktop,

ensure there are 10 mm

between the upper pa-

nel of the dryer and any

objects above it, and 15

mm between the sides

of the machine and the

walls or furniture units

adjacent to it. This ensu-

res adequate air circu-

lation. Make sure the air

inlets on the rear panel are not blocked or

obstructed.

Ventilation

This appliance gently dries laundry by taking in cold, clean

and relatively dry air, heating it and passing it through the

fabric. To facilitate the drying process, damp air is expelled

at the rear, through a ventilation hose. When the dryer is in

use, there has to be adequate ventilation to avoid a back

flow of gases into the room from appliances burning other

fuels, including open fires.

Mobile ventilation system

When using the tumble dryer with the mobile ventilation

system, a ventilation hose must be connected. The hose

should be securely fastened to the ventilation hole at

the rear of the appliance (see "Description of the tumble

dryer"). We recommend the hose is connected to an outlet

near the tumble dryer, if possible. If it cannot be installed

in a permanent spot, the tumble dryer will still function

perfectly well if the ventilation hose is passed through a

partially-opened window.

Make sure you do not point the ventilation hose towards

the air inlet, which is located on the rear of the appliance.

The ventilation hose should not exceed a maximum

length of 2.4 metres; it should also be shaken frequently

to remove any fluff, dust or water deposits inside it. Make

sure you do not crush the hose.

oval section to aid installation.

Fixed ventilation

kit

We recommend the ventilation hose is connected to a

ventilation

kit

for windows or doors, available from the

retailer which originally sold you the appliance or from your

local spare parts stockist.

Wall ventilation hole

checked frequently, to prevent the accumulation of fluff or

15 mm

The hose supplied has an

1. Leave an opening in the wall.

2. Make the hose as short and

straight as possible, in order

to prevent any moisture from

condensing and leaking back

into the appliance.

3. The hole in the wall must

also be straight and pointing

downwards, so that the flow of

air coming out is not impeded.

Areas A and B should be

debris, particularly if the tumble dryer is used very often.

The hose adaptor must be fitted correctly, in order to

prevent damp air from coming back into the room.

GUIDE TO FITTING THE VENT HOSE TO YOUR DRYER

please wear gloves when cutting the hose.

vent hose to a wall mounting kit (not supplied).

clip will not clamp the hose to the rear vent outlet.

The tumble dryer may protrude further forward from the

worktop. Please do not push the tumble dryer too far

backwar.

Ventilation hole

The ventilation hole should be directly behind the dryer in

order to keep the hose as short as possible.

Make sure you do not push the tumble dryer too far

backwards, as this could lead to the ventilation hose being

crushed, bent or even disconnected.

There should be no cuts, kinks or "U"-shaped bends

in the hose, as these could impede ventilation or trap

condensation.

The end of the hose must be facing downwards, in order to

prevent the hot, damp air from forming condensation in the

room or the tumble dryer.

Make sure that the tumble dryer is adequately ventilated,

and that the end of the ventilation hose is not pointing

towards the air inlet pipe on the rear of the appliance.

The ventilation hose must always be fitted to ensure

optimum performance.

Remove 'oval-shaped'

Ventilation hose from

the packaging.Ensure

that you also remove

the two jubilee clips.If

you require to reduce

the length of the hose

Pull to expand the end

of the Ventilation hose

prior to fitting.

If the hose has not

been expanded, the

jubilee clip will not

clamp the hose to the

adaptor.

Place one of the the

jubilee clips over the

end of the extended

vent hose.

The second jubilee clip

can be used to secure

the opposite end of the

Clamp the ventilation

hose to the rear vent

outlet by tightening

the jubilee clip with a

screwdriver.

If the hose has not

been expanded, the