Kohler Intaglio K-2292 Installation Instructions Manual - Page 3

Browse online or download pdf Installation Instructions Manual for Bathroom Fixtures Kohler Intaglio K-2292. Kohler Intaglio K-2292 16 pages. Countertop and undercounter lavatories
Also for Kohler Intaglio K-2292: Homeowner's Manual (16 pages), Homeowner's Manual (24 pages)

Print Page

Kohler Intaglio K-2292 Installation Instructions Manual

DRAW PRELIMINARY FAUCET CENTERLINE

Draw the distance determined in FAUCET LOCATION as the

preliminary centerline on the cut-out template. It should be parallel

and behind the cut-out template reference line (located on the

cut-out template).

NOTE: On the full-size rim section found on the cut-out

template, mark the preliminary faucet centerline dimension.

This will be used to DETERMINE FINAL FAUCET CENTER-

LINE.

DETERMINE FINAL FAUCET CENTERLINE

NOTE: If you are installing a tiled-in lavatory, proceed to Step 1B.

The preliminary faucet line from DRAW PRELIMINARY

FAUCET LINE is the final faucet line in this case.

When this preliminary faucet centerline has been drawn the

spout must be checked for three items:

Refer to Fig. #2. For low profile faucet spouts, the

distance between the faucet spout and the lavatory rim must be a

minimum of 1/4" (6mm). Use the faucet spout, the preliminary

faucet centerline, and the full size rim section on the cut-out template

to check this. If there is not 1/4" (6mm) clearance, move the

preliminary faucet centerline back. Recheck the clearance until you

have 1/4" (6mm). Measure the distance of the new faucet centerline.

Redraw the new faucet centerline behind the reference line on the

cut-out template. Remark this dimension on the full size rim section.

This is the final faucet centerline.

Fig. #3

Refer to Fig. #3. Check to be sure the water stream will

project 2" (5cm) minimum into the lavatory basin to allow adequate

area for hand washing. Use the approximate faucet spout angle, the

final faucet centerline and the full-size rim section from the cut-out

template to ensure this clearance. If this cannot be accomplished,

the faucet is not optimally matched for this lavatory and may not

operate on this lavatory to the owner's satisfaction. You may wish to

consider an alternate faucet.

Refer to Fig. #3. Check for compliance with all state and

local plumbing codes, including air gap standards.

1007251-2-

1/4" (6mm)Min.

2" (5cm) Min.

FAUCET CLEARANCE WITH BACKSPLASH

NOTE: 2-1/2" (6,4cm) of space is required for the Kohler Bravura

widespread and Cirrus Sheetflow faucet spouts.

Refer to Fig. #4. Draw a line 2" (5cm) behind the final faucet

centerline on the cut-out template. This is the minimum backsplash

locator line. It is drawn to ensure adequate clearance behind the

faucet for proper installation. It will also help position the lavatory on

the countertop. Cut along this backsplash locator line. Save the

section of the cut-out template with the lavatory rim and cut-out

lines.

Countertop Backsplash Backsplash Locator Line

(5cm)

INSTALLATION

. To remove old lavatory, turn off water supplies. Turn the

lavatory faucet on to drain water from the lines. Disconnect and

remove water supply tubes. Disconnect drain and remove trap.

CAUTION:

To remove steel frame lavatories, remove

clips or fasteners under lavatory that hold lavatory to counter.

Do not remove clips that hold frame to fixture.

2" (5cm)

Min.

Fig. #4

C L of Fitting

Cut-Out Template

On Countertop

Countertop

Fig. #5

Air

Gap

Kohler Co.