Kohler JULY 5428T-C4 Installation Instructions - Page 2

Browse online or download pdf Installation Instructions for Bathroom Fixtures Kohler JULY 5428T-C4. Kohler JULY 5428T-C4 2 pages. Wall-mount bath & dual shower straight column

Print Page

INSTALLATION

How to Install the Faucet

To perform installation, installer must provide G1/2˝ female supply

fittings(1), spaced 150mm apart and horizontally. The supply fittings

should be vertical and not beyond the finished wall. Hot supply pipe

must be located on the left.

Flush the water supply pipes thoroughly to remove debris.

Install the two offset connectors(2) into the hot and cold supply pipes.

Use appropriate thread sealants or thread tape on pipe threads.

Adjust the center-to-center distance between the connectors to 150mm

and horizontally. Thread the escutcheons(3) onto the connectors until

they are against the finished wall.

Put the washers(4) into the nuts(5), thread the nuts to connectors.

Tighten the nuts with strap wrench or soft cloth between product and

regular wrench.

How to Install the Column

Select a location in vertical wall to install shower column according to

rough-in dimensions.

Drill the lower hole as anchors(6) diameter and lower base(8-1) position

in the finished wall(NOTE: The arrow in the base is upward). Press

anchors into the hole, secure the base by the screw(7).

Rehearse the slide bar kit(9) installation for the upper base(8-2) mounting

location determination. Slide the tube joint(10) onto the slide bar kit, and

connect them to the base(NOTE: The arrow in the base is upward).

Install the screws(12) into the tube joint with the hex wrench(11), and

tighten them.

Place the slide bar and the body against the finished wall. Connect the

lower base and the diverter body kit(13). Position and tighten them by

hex wrench. Mark the hole of upper base(8-2) with a pencil. Uninstall the

slide bar kit and tube joint.(NOTE: Don't lose the screws.)

Drill holes on the mark. Press the anchors into the holes. Secure the

upper base(8-2) by the screws. Install the tube joint(10) to the base(8-2)

and tighten them by screws. Reinstall the slide bar kit with escutcheons

(14) to the bases. Tighten the screws with the hex wrench. Screw the

escutcheons with the bases until against the finished wall.

Install the tube kit(15) into the slide bar kit. Install the nut(16) onto the

tube kit with soft cloth between internal hole of the nut and the tube kit.

Then screw the nut onto the slide bar kit with strap wrench or soft cloth

between the nut and regular wrench.

1265601-2A-A

Cold

Hot

8-2

8-1

How to Install the Handspray and the Hose

Before install handspray(17), turn the diverter handle(18) right to close

the wall and run hot and cold water for about one minute to remove any

debris.

Put the check valve(19) into the handspray inlet if needed. Connect the

hose(20) to the handspray, and to the connector(22) with the

washers(21). Connect the hose(23) to the faucet outlet(25), and to the

connector(26) with the washers(24).

How to Install the Showerhead

Before install showerhead(27), turn the diverter handle vertically to the

wall and run hot and cold water for about one minute to remove any

debris.

Install the restrictor(28) if needed. Take out the washer(29) and install the

restrictor as shown, reinstall the washer. Tighten the showerhead onto

the tube outlet with strap wrench.

INSTALLATION CHECKOUT

Ensure that all connections are tight. Ensure that the handle is in the off

position.

Turn on the drain and main water supply, and check for leaks. Repair as

needed.

Remove the aerator(30). Turn on the faucet. Run hot and cold water

through the spout for about one minute to remove any debris. Check for

leaks. Remove any debris from the aerator. Shut off the faucet. Reinstall

the aerator.

CLEANING INSTRUCTIONS

All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft

cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc. which could adversely

affect the finish and are not recommended for cleaning.

Do not use abrasive cleaners or solvents on Kohler faucets and fittings.

1265601-2A-A