Dell PowerVault TL4000 Software Manual - Page 8

Browse online or download pdf Software Manual for Storage Dell PowerVault TL4000. Dell PowerVault TL4000 16 pages. Tape library
Also for Dell PowerVault TL4000: Release Notes (3 pages), Getting Started (38 pages), Faq (26 pages), Quick Start Manual (7 pages), Configuration Manual (22 pages), Important Information Manual (10 pages), User Manual Addendum (2 pages), Getting Started Manual (3 pages), Attachment Instructions (17 pages), Brochure (4 pages), User Manual (20 pages)

Dell PowerVault TL4000 Software Manual

Using Linux Server

1) Edit the /etc/iscsi.conf file to add the entries below for each iSCSI target:
For example, your edited /etc/iscsi.conf file might look like this:
DiscoveryAddress=172.168.10.6
OutgoingUsername=iqn.1987-05.com.cisco:01.742b2d31b3e
OutgoingPassword=0123456789abcdef
Note: If you are configuring Mutual CHAP authentication in Linux, you must also add an
IncomingUsername= and IncomingPassword= entry after each
OutgoingPassword= entry.
The IncomingUsername is the iSCSI target name, which can be viewed in the iSCSI
bridge management interface
For example, your edited /etc/iscsi.conf file might look like this:
DiscoveryAddress=172.168.10.6
OutgoingUsername=iqn.1987-05.com.cisco:01.742b2d31b3e
OutgoingPassword=0123456789abcdef
IncomingUsername=iqn.1984-05.com.dell:powervault.6001372000f5f0e600000000463b9292
IncomingPassword=abcdef0123456789

If you are using RHEL 5 or SLES 10 SP1

1) To enable CHAP, add the following line to your /etc/iscsi/iscsid.conf file.
node.session.auth.authmethod = CHAP
2) To set a username and password for CHAP authentication of the initiator by the target(s), edit the
following lines as shown:
node.session.auth.username = <iscsi_initiator_username>
node.session.auth.password = <CHAP_initiator_password>
3) If you are using Mutual CHAP authentication, you can set the username and password for CHAP
authentication of the target(s) by the initiator by editing the following lines:
node.session.auth.username_in= <iscsi_target_username>
node.session.auth.password_in = <CHAP_target_password>
4) To set up discovery session CHAP authentication, first uncomment the following line:
discovery.sendtargets.auth.authmethod = CHAP
5) Set a username and password for a discovery session CHAP authentication of the initiator by the
target(s) by editing the following lines:
discovery.sendtargets.auth.username = <iscsi_initiator_username>
discovery.sendtargets.auth.password = <CHAP_initiator_password>
6) To set the username and password for discovery session CHAP authentication of the target(s) by
the initiator for Mutual CHAP, edit the following lines:
discovery.sendtargets.auth.username = <iscsi_target_username>
discovery.sendtargets.auth.password_in = <CHAP_target_password>
7) As a result of steps 1 through 6, the final configuration contained in the /etc/iscsi/iscsid.conf file
might look like this:
node.session.auth.authmethod = CHAP
node.session.auth.username = iqn.2005-03.com.redhat01.78b1b8cad821
node.session.auth.password = password_1
node.session.auth.username_in= iqn.1984-
05.com.dell:powervault.123456
node.session.auth.password_in = test1234567890
discovery.sendtargets.auth.authmethod = CHAP
discovery.sendtargets.auth.username = iqn.2005-
03.com.redhat01.78b1b8cad821
discovery.sendtargets.auth.password = password_1
discovery.sendtargets.auth.username = iqn.1984-
05.com.dell:powervault.123456
discovery.sendtargets.auth.password_in = test1234567890

If you are using SLES10 SP1 via the GUI

1) Select Desktop−> YaST−>iSCSI Initiator.
Page 8