Dialogic Dialogic 64-0074-02 Quick Install Card - Page 2

Browse online or download pdf Quick Install Card for Computer Hardware Dialogic Dialogic 64-0074-02. Dialogic Dialogic 64-0074-02 2 pages. Media board

Print Page

5. Using the slot's board guides, insert the board's edge

connector into the bus slot. Press firmly until the

board is securely seated in the slot.

Installing a PCI Board

Remove

Cover

Plate

Computer

Chassis

32-Bit

PCI Slot

6. Replace and tighten the slot's retaining screw to

secure the board firmly in the chassis (if applicable).

7. Connect external digital telephone cables to the

RJ-48C jacks on the board bracket. The topmost

RJ-48C jack is for trunk 1 and the second RJ-48C

jack is for trunk 2.

Pinouts for the RJ–48C

Network Interface

Jacks on Bracket

Cable Connector

RCV_RING

Pin 1

RCV_TIP

CHASSIS GROUND

XMIT_RING

XMIT_TIP

CHASSIS GROUND

8. Repeat steps 3-7 for each additional board you are

installing.

9. Use the CT Bus cable to connect the board(s) you

are installing to other boards in the system. To

preserve the electrical integrity of the CT Bus, use a

CT Bus cable with the appropriate number of

connectors ("drops"). It is recommended that no more

than two connectors at either end of the cable be left

unused.

10. Your system may include both CT Bus and SCbus

boards. To connect both board types, you must

install a CT Bus/SCbus Adapter on one of the CT

Bus boards in a system. See the CT Bus/SCbus

Adapter Quick Install Card for installation details

about the Adapter and the bus cables

Installing the CT Bus Cable

PCI

Board

16-Bit

ISA Slot

11. Install CT Bus Termination Jumpers only on boards

located at each end of the CT Bus cable. See the

"Physical Description" section for jumper details.

12. Replace the computer's cover when finished and

reconnect the power cords.

13. Turn the computer's power ON.

CAUTION: If your BIOS is set to use Plug and Play

technology and there are ISA boards in your system, an

IRQ conflict can be created if a PCI board is assigned

the same IRQ as an ISA board. This could cause the

machine to stop responding. You can prevent this by

entering the BIOS and reserving the appropriate IRQs

(those used by your ISA boards) for ISA use only.

After installing the hardware, run the Dialogic

Configuration Manager (DCM) as described in the

installation instructions included with the Dialogic

System Software to configure your system.

For technical specifications and product information go

to: http://www.dialogic.com/products.htm.

Warranty and Return Information

For specific warranty information for this board, refer to

the Warranty section of the Products page, located at

this URL: http://www.dialogic.com/warranties/.

Dialogic provides technical support for its products

through a network of value added distributors who are

trained to answer technical questions on installing and

configuring Dialogic

to contact your support channel, please call Dialogic

in the United States at 973-967-6600 (9am-5pm EST)

and we will assist in obtaining the appropriate support

channel. Outside the United States please refer to

http://www.dialogic.com/support/contact

Colored

Stripe

(Pin 1)

Note:

Your CT Bus cable may

have a different number

of connectors (drops).

After Installing the Hardware

Warranty Period

Contacting Technical Support

products. If you are unsure how

Dialogic also provides direct support via Dialogic

CT Bus

Cable

Services agreements. For more details of direct support

from Dialogic please refer to:

http://www.dialogic.com/support/DialogicPro.

To return a board for warranty or any other returns,

please refer to the following:

http://www.dialogic.com/support/hwfaults .

If you have a sales question, please contact your

local Sales Representative or the Regional Sales Office

for your area. Address, telephone and fax numbers, are

available at the Dialogic website located at:

http://www.dialogic.com/contact.htm

Dialogic

products, please refer to the following website

to locate the appropriate supplier:

http://www.dialogic.com/purchase.htm

All contents of this document are furnished for informational use only and are subject to

change without notice and do not represent a commitment on the part of Dialogic Corporation

or its subsidiaries ("Dialogic"). Reasonable effort is made to ensure the accuracy of the

information contained in the document. However, Dialogic does not warrant the accuracy of

this information and cannot accept responsibility for errors, inaccuracies or omissions that may

be contained in this document.

INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH

DIALOGIC

PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR

OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS

DOCUMENT. EXCEPT AS PROVIDED IN A SIGNED AGREEMENT BETWEEN YOU

AND DIALOGIC, DIALOGIC ASSUMES NO LIABILITY WHATSOEVER, AND

DIALOGIC DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO

SALE AND/OR USE OF DIALOGIC PRODUCTS INCLUDING LIABILITY OR

WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE,

MERCHANTABILITY, OR INFRINGEMENT OF ANY INTELLECTUAL PROPERTY

RIGHT OF A THIRD PARTY.

Dialogic products are not intended for use in medical, life saving, life sustaining, critical

control or safety systems, or in nuclear facility applications.

It is possible that the use or implementation of any one of the concepts, applications, or ideas

described in this document, in marketing collateral produced by or on web pages maintained

by Dialogic may infringe one or more patents or other intellectual property rights owned by

third parties. Dialogic does not provide any intellectual property licenses with the sale of

Dialogic products other than a license to use such product in accordance with intellectual

property owned or validly licensed by Dialogic and no such licenses are provided except

pursuant to a signed agreement with Dialogic. More detailed information about such

intellectual property is available from Dialogic's legal department at 9800 Cavendish Blvd., 5

Floor, Montreal, Quebec, Canada H4M 2V9. Dialogic encourages all users of its products to

procure all necessary intellectual property licenses required to implement any concepts

or applications and does not condone or encourage any intellectual property

infringement and disclaims any responsibility related thereto. These intellectual property

licenses may differ from country to country and it is the responsibility of those who

develop the concepts or applications to be aware of and comply with different national

license requirements.

Dialogic, Diva, Eicon, Eicon Networks, Eiconcard and SIPcontrol, among others, are either

registered trademarks or trademarks of Dialogic. Dialogic's trademarks may be used publicly

only with permission from Dialogic. Such permission may only be granted by Dialogic's legal

department at 9800 Cavendish Blvd., 5th Floor, Montreal, Quebec, Canada H4M 2V9. Any

authorized use of Dialogic's trademarks will be subject to full respect of the trademark

guidelines published by Dialogic from time to time and any use of Dialogic's trademarks

requires proper acknowledgement. The names of actual companies and products mentioned

herein are the trademarks of their respective owners.

Pro™

Returning a Product

Sales Assistance

. To purchase