Dialogic Dialogic Media Board DMV600BTEC Quick Install Card - Page 2

Browse online or download pdf Quick Install Card for Computer Hardware Dialogic Dialogic Media Board DMV600BTEC. Dialogic Dialogic Media Board DMV600BTEC 2 pages. Media board

Print Page

Note: If the power to the chassis is on when you

insert the board, power is immediately applied to

the board, the Out of Service LED lights briefly and

then goes out, and the Power LED goes on.

CAUTION: CompactPCI backplane pins are easily

bent. Make sure that the board connectors are

mating properly with hand pressure before fully

seating the board. When using the board extractors

to seat the board, make sure to seat evenly.

Installing cPCI Baseboard

Compact PCI

Backplane

Unlocked

Position

C I

t P

a c

a r d

m p

b o

C o

s e

B a

Locked

Position

Compact PCI

Chassis

External Connections

6. For an RJ48C (T1 or 120-Ohm E1) I/O module,

connect the external digital telephone cables to the

RJ-48C jacks on the board bracket. The topmost

RJ-48C jack is for trunk 1 and the second jack is

for trunk 2. The pinout for the RJ48C connectors is

given in the following figure

7. For a BNC (75-Ohm E1) rear I/O module, connect

the external digital telephone cables to the BNC

connectors. The top two BNC connectors (T1 and

R1) are for trunk 1, and the next two connectors

(T2 and R2) are for trunk 2.

RJ48C Connector Pinout

Network Interface

Pinout for RJ–48C Jacks

Cable Connector

on Rear I/O Module

Chassis Ground

Pin 1

Unused

XMIT_TIP

XMIT_RING

Unused

RCV_TIP

RCV_RING

Completing the Installation

8. Select a new slot and repeat steps 3-7 for each

board you are installing.

9. Replace the front and back cover plate or close

the front and back chassis doors, as appropriate.

10. If the power to the chassis was turned OFF in step

1, turn the power to the chassis ON.

After Installing the Hardware

For a new installation, proceed with the software

installation as described in the Dialogic

System

Software documentation.

Note: If you are adding hardware to an existing

telecom system, you do not need to uninstall or

reinstall existing Dialogic

System Software.

For technical specifications and product information

go to:

http://www.dialogic.com/products.htm.

Removing the Hardware

Exercise caution when removing boards from a

CompactPCI chassis. The board extractors are

equipped with red locking tabs that latch when the

board is correctly positioned in the chassis.

Attempting to extract a board without first releasing

the locks may break the lock mechanism.

Removing the Baseboard

Before removing the baseboard, ensure that you are

properly grounded. To remove the baseboard from

the chassis, simultaneously press down both red

locking tabs on the extractors (see the figure below),

then evenly press the extractors away from the center

of the board to release the board from the chassis.

CAUTION: If the red locking tabs on the extractors

are not pressed before applying pressure to the

extractors, there is a risk of breaking the tabs.

After removing the baseboard, immediately place it on

a static-safe work surface or insert it into an anti-static

container.

CompactPCI Board Extractor

P r e s s a n d h o l d d o w n

t h e r e d l o c k i n g t a b s o n

b o t h b o a r d e x t r a c t o r s

b e f o r e a p p l y i n g

p r e s s u r e t o t h e b o a r d

e x t r a c t o r s

Removing the Rear I/O Module

Note: In a live insertion (powered-on) system, do not

remove and replace a rear I/O module while the

baseboard is in service. Remove the front board first,

then remove and replace the rear I/O module, and

then reinsert the baseboard.

To remove the rear I/O module from the chassis,

simultaneously press down both red locking tabs on

the extractors (see the figure above) then evenly

press the extractors away from the center of the

module to release the module from the chassis.

CAUTION: If the red locking tabs on the extractors

are not pressed before applying pressure to the

extractors, there is a risk of breaking the tabs.

Warranty and Return

Information

Warranty Period

For specific warranty information for this board, refer

to the Warranty section of the Products page, located

at this URL: http://www.dialogic.com/warranties/.

Contacting Technical Support

Dialogic provides technical support for its products

through a network of value added distributors who are

trained to answer technical questions on installing and

configuring Dialogic

products. If you are unsure how

to contact your support channel, please call Dialogic

in the United States at 973-967-6600 (9am-5pm EST)

and we will assist in obtaining the appropriate support

channel. Outside the United States refer to

http://www.dialogic.com/support/contact

to obtain

local contact information. Dialogic also provides direct

support via Dialogic

Pro™ Services agreements. For

more details of direct support from Dialogic refer to:

http://www.dialogic.com/support/DialogicPro.

Returning a Product

To return a board for warranty repair or any other

returns, please refer to the following:

http://www.dialogic.com/support/hwfaults.

Sales Assistance

If you have a sales question, please contact your

local Sales Representative or the Regional Sales

Office for your area. Address, telephone and fax

numbers, are available at the Dialogic website located

at:

http://www.dialogic.com/contact.htm

To purchase Dialogic

products, please refer to the

following website to locate the appropriate supplier:

http://www.dialogic.com/purchase.htm.

All contents of this document are furnished for informational use only and are

subject to change without notice and do not represent a commitment on the part of

Dialogic Corporation or its subsidiaries ("Dialogic"). Reasonable effort is made to

ensure the accuracy of the information contained in the document. However,

Dialogic does not warrant the accuracy of this information and cannot accept

responsibility for errors, inaccuracies or omissions that may be contained in this

document.

INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION

WITH DIALOGIC

PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY

ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY

RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN A

SIGNED AGREEMENT BETWEEN YOU AND DIALOGIC, DIALOGIC

ASSUMES NO LIABILITY WHATSOEVER, AND DIALOGIC DISCLAIMS

ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR

USE OF DIALOGIC PRODUCTS INCLUDING LIABILITY OR

WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE,

MERCHANTABILITY, OR INFRINGEMENT OF ANY INTELLECTUAL

PROPERTY RIGHT OF A THIRD PARTY.

Dialogic products are not intended for use in medical, life saving, life sustaining,

critical control or safety systems, or in nuclear facility applications.

It is possible that the use or implementation of any one of the concepts,

applications, or ideas described in this document, in marketing collateral produced

by or on web pages maintained by Dialogic may infringe one or more patents or

other intellectual property rights owned by third parties. Dialogic does not provide

any intellectual property licenses with the sale of Dialogic products other than a

license to use such product in accordance with intellectual property owned or

validly licensed by Dialogic and no such licenses are provided except pursuant to a

signed agreement with Dialogic. More detailed information about such intellectual

property is available from Dialogic's legal department at 9800 Cavendish Blvd., 5

Floor, Montreal, Quebec, Canada H4M 2V9. Dialogic encourages all users of its

products to procure all necessary intellectual property licenses required to

implement any concepts or applications and does not condone or encourage

any intellectual property infringement and disclaims any responsibility

related thereto. These intellectual property licenses may differ from country

to country and it is the responsibility of those who develop the concepts or

applications to be aware of and comply with different national license

requirements.

Dialogic, Diva, Eicon, Eicon Networks, Eiconcard, Dialogic Pro and SIPcontrol,

among others, are either registered trademarks or trademarks of Dialogic.

Dialogic's trademarks may be used publicly only with permission from Dialogic.

Such permission may only be granted by Dialogic's legal department at 9800

Cavendish Blvd., 5th Floor, Montreal, Quebec, Canada H4M 2V9. Any authorized

use of Dialogic's trademarks will be subject to full respect of the trademark

guidelines published by Dialogic from time to time and any use of Dialogic's

trademarks requires proper acknowledgement. The names of actual companies and

products mentioned herein are the trademarks of their respective owners.