AQUAPHOR S800 Operation Manual - Page 12

Browse online or download pdf Operation Manual for Water Dispenser AQUAPHOR S800. AQUAPHOR S800 20 pages.

Print Page

• power supply connector.

• Lay the power supply wire at the outlet of the wa-

ter lines. Connect the power supply to an outlet.

• Make sure the outlet to which the softener is con-

nected does not have an ON/OFF switch.

Step 8. Adjust the softener controller according to

the Controller Setup section.

Step 9. Rinse the softener

• Pour 8 l of water into the brine tank.

• Make sure the softener is in filtration mode and the

water supply is turned on.

• Perform a forced regeneration. To do this, press and

hold the R button for about 5 seconds until the num-

bers 01 appear on the display and the regeneration

process starts.

• During the regeneration, which lasts 30–40 minutes,

the device will first take and then add water to the

brine tank to the desired level.

ATTENTION! The brine tank should only be filled with

water when the softener is started. After starting, top-

ping up water is carried out automatically.

Step 10. Load Salt into the Brine Tank

Load salt into the brine tank up to 25 kg. Use refined table

salt or granulated table salt (NaCl). Do not use these two

types of salt at the same time. Use only high-quality tab-

leted or granulated salt, such as AQUAPHOR. Poor quali-

ty salt can cause a decrease in the efficiency of regener-

ation or the failure of the softener.

NOTE: Always keep the salt level above the water level.

For convenience, when adding salt, fully load the tank.

After adding salt, including adding after salt is complete-

ly used up, wait at least two hours before starting regen-

eration. This is necessary for the formation of a saturated

saline solution.

Step 11. Complete the installation process

Make sure the bypass valve is in the "Service" position

(see fig. 1).

Make sure the water supply is turned on.

If there is an external bypass circuit, make sure the taps

are in the correct position (see fig. 5).

Turn on the power and water supply to the water heater

(if any). For gas water heaters, turn the gas valve to the

"Operation" position (see the instructions for your water

heater).

Open the nearest cold water faucet and run the softener

for 20 minutes or until about 270 liters water.

Make sure that the water consumption indicator on the

controller display is working – this indicates the water

consumption and the operation of the liter counter.

Replace the softener cover.

Controller setup

For the correct operation of the softener, it is necessary

to enter into the processor data on the content of hardness

salts, iron and manganese in the water.

To do this, it is necessary to calculate the total parameter,

which will include all these pollutants. This parameter is

called "compensated stiffness".

Generally, in water analysis, total hardness is expressed

in mg-eq / l.

ATTENTION! German (DH) and French (ºF) are differ

from mg-eq / l.

To calculate the "compensated stiffness"

it is necessary:

• Multiply the number of mg-eq / l by 50.

• Add the concentrations of iron (mg/l) and manganese

(mg/l) and multiply the sum by 85.

• Add up both items.

EXAMPLE:

Total hardness = 6.84 mg-eq / l

Ferrous iron (dissolved) = 3 mg/l

Manganese = 1 mg/l

Compensated stiffness = 6.84 × 50 + (3+1) × 85 = 682

Note. If the total hardness is presented in the analysis as

a concentration of CaCO

multiply the value by 50.

EXAMPLE:

General hardness = 342 mg/l CaCO

Ferrous iron (dissolved) = 3 mg/l

Manganese = 1 mg/l

Compensated stiffness = 342 + (3+1) * 85 = 682

If you have any questions, please contact Aquaphor sup-

port.

Quick Setup / Basic Settings

Step 1. Set the hardness value

A. Click

. After approximately 4 seconds, the con-

troller will beep and the display will show ppm

B. Press

until the number on the display corre-

sponds to the required hardness to be compensated

(see section "Checking before installation").

C. Click

to save the settings and proceed to the

next step.

Step 2. Setting the current time

A. Press

until you set the current hour. Press

to save the setting and move on to setting the min-

utes.

B. Press

until you set the current minutes. Press

to save the setting and go to the home screen.

NOTE: The current time is shown in 24 hour format.

(mg/l), it is not necessary to