Diamond DT224/PMA+EV Instruction Manual - Page 4

Browse online or download pdf Instruction Manual for Refrigerator Diamond DT224/PMA+EV. Diamond DT224/PMA+EV 8 pages.

Print Page

The European directive on Waste from Electrical and Electronic Equipment (WEEE) specifies that, at the end of its life

cycle, the equipment and all of its components, subassemblies and consumable materials should be sent separately

for treatment for it to be destroyed, recycled or reused.

Do not put equipment with this symbol together with unseparated urban waste.

3. Recommendations for Installation

3.1 - General Notes

Although the construction and operation of every counter is controlled on the factory floor, this does not invalidate the possibility

that damage may be caused during transportation. Thus upon reception we advise that the general condition of the counters

should be verified.

3.2 - Placement

Remove the packaging or pallet with care so as not to damage the surfaces of the equipment.

With a pallet-lifter, lift the refrigerating cupboard and take it to the place for installation.

Remove the protective plastic from the outside. This operation could cause small electric shocks, but which are of no

consequence, as they involve merely static electricity. This inconvenience can be reduced or eliminated by always having a

hand on the machine or connecting the earth wire to the outer packaging.

Once the cupboard has been placed in position, remove the packaging or pallet with a chisel and hammer, paying attention

so as not to damage the feet or the cupboard itself.

It is advisable to place the cupboard away from any possible heat sources (like heaters) and of the sunlight.

Do not cover or obstruct the cupboard top - must be guarantee free space to this area, assuring a good air circulation.

In order to ensure a proper operation of the cupboard, it should always be on the level. Small differences in level can be

compensated by regulating the feet.

For models which do not contain automatic condensation water evaporation systems, a tray must be put in the lower part of

the cupboards, and should be emptied out on a regular basis.

3.3 - Installation

Installation should be carried out with the following standards always being borne in mind:

Regulations referring to the construction of the buildings and fire-precautions.

Regulations in force concerning accident prevention.

European Union Standards which may be in force.

The cupboard is supplied with a plug in accordance with current standards of practice and with an electricity supply power

cable according to the regulations with a length which is sufficient to allow connection to the electricity current.

The electrical socket should be easily accessible and organised so that maximum consumption is available (see data from the

Table of Technical Terms). The socket should be EARTHEN.

Never use plugs or sockets without earth, nor use adapters or extension wires.

For direct connections to the network, a fuse switch should always be installed in accordance with international regulations.

3.4 - Substitution of the Electricity Supply Cable

Pull the power cord from the plug

The terminal board is in the compressor compartment (back side). Remove the cover of the terminal board.

Loosen the fastening device from the cord at the bottom of the compartment.

To remove the conductors, loosen the terminals and replace the cable. The new one must have at least the characteristics on

the Technical Data Table. The earth wire must be longer than the phase and neutral wires.

The Ensure that the supply cable is not subject to traction and that it does not contain coils or knots which could create heat.

The manufacturer declines any responsibility both for the operation, and for damage or losses caused, which result from lack of

observing recommendations in this instruction manual.

4. Recommendations for the User

Refrigerated counters were conceived in order to conserve food during short periods of time and for food products in general.

In order to ensure that the machine is operating properly it is necessary to follow the following instructions:

Children should be supervised to ensure that they do not play with the device.

Avoid opening the doors and drawers as much as possible.

MNS00027.02

TEC

INSTRUCTIONS MANUAL

Power cord:

- type

- Nominal section

- Manufacture code (normal)

HO5VVF

3 x 1.5 mm2

43001004

(England)

43001001

N.º

MNS00027.02

10/45