Panasonic U-20ME1E81 Installation Manual - Page 4
Browse online or download pdf Installation Manual for Digital Camera Panasonic U-20ME1E81. Panasonic U-20ME1E81 9 pages. Wall mounted (k1 type),
mini vrf (le1 type),
2way vrf (me1 type),
3way vrf (me2 type)
Also for Panasonic U-20ME1E81: Quick Reference Manual (24 pages), Operating Instructions Manual (26 pages), Operating Instructions Manual (25 pages), Installation Instructions Manual (25 pages), Installation Instructions Manual (28 pages), Operating Instructions Manual (10 pages)
Print Page
If two or more separable connectors are
provided,
they
shall
arranged so that the other and vice-versa
will not accept the mating connector for
one,
if
it
will
result
connection.
Connectors
between
modules
inserted until they click.
Do
not
put
too
connectors in order to avoid detachment
of connectors.
Please contact your Panasonic Authorized
Representative
with
questions
other electrical connections if needed.
Junction Box and Terminals
Modules equipped with one junction box
contain terminals for both positive and
negative polarity, and bypass diodes.
One terminal is dedicated to each polarity
(with the polarity symbols engraved onto
the
body
of
the
junction
Figure 3).
Conduit
For applications where wire conduits are
used,
follow
the
applicable
outdoor installation of wires in conduits.
Minimum diameter of wire conduit is 4
2
mm
.
Verify that all fittings are properly installed
to
protect
wires
against
prevent moisture intrusion.
DIODES
Bypass Diodes
When the modules in series strings are
shaded partially, it may cause reverse
voltage across cells or modules, because
the current from other cells in the same
series
is
forced
to
shaded area. This may cause undesirable
heating to occur.
The
use
of
a
diode
shaded area can minimize both heating
and array current reduction.
All modules are equipped
installed
bypass
diodes.
installed
diodes
provide
protection
for
the
systems
specified system voltage, so that you do
not
need
any
other
diodes.
Specifications
of
bypass
VBHNxxxSJ25
series
Number
of
bypass
Number of series cells per bypass diode:
24 cells / diode. Specifications of bypass
diode for VBHNxxxSJ40 series are as
follows;
Number
of
diodes, Number of series cells per bypass
diode: 22 cells / diode (See Figure 4).
Contact
your
Panasonic
Representative for proper diode type, if it
be
configured
or
in
an
improper
must
be
much
stress
on
regarding
is necessary to add or change diodes
due to system specifications.
MAINTENANCE
box)
(see
Some
maintain optimal output performance of the
modules.
It is also recommended to inspect the
electrical
codes
for
annually.
If
inspection
recommended
authorized
damage
and
inspection or maintenance to avoid the
hazards of electric shock or injury.
The return of any modules will not be
accepted by Panasonic unless prior written
authorization has been given by Panasonic.
As
improvement Panasonic reserves the right
to change product specifications at any
time without prior notice.
flow
through
the
Anti-reflection Glass surface cleaning
Cleaning of dirt
to
bypass
the
If the module surface becomes dirty, it
may reduce output power.
It is recommended to clean the surface
with factory
of the module with water and a soft cloth
The
factory
or sponge.
proper
circuit
To remove persistent dirt, the module
within
the
can be washed with a micro-fiber cloth
and ethanol.
additional
bypass
Never
alkaline
diode
for
detergent to clean any part of the module.
are
as
follows;
Performance
diode:
3
diodes,
reduced. Please be very careful since
warranty will not cover the damage from
detergent.
When
bypass
diode:
4
recommended to start with smallest area
and from the edge of solar panel in
order to check no damage occurs to the
Authorized
glass.
24 cells / diode
24 cells / diode
24 cells / diode
VBHNxxxSJ25 series
Figure 4: Number of series cells per
maintenance
is
recommended
and
mechanical
connections
you
need
electrical
or
mechanical
or
maintenance,
to
have
a
professional
carry
part
of
our
policy
of
use
abrasive
detergent,
detergent
and
strong
of
solar
panel
cleaning
with
detergent,
4
VBHNxxxSJ40 series
bypass diode
It is recommended to read carefully the
manuals
of
notes on usage and first-aid treatment.
to
Cleaning of soiling from handling
Unlike
the
surface from holding the glass will not
affect
performance
Therefore cleaning is not necessary for
this soil on glass surface caused by
handling.
it
is
cleaning, following is the recommendation
licensed
of cleaning methods.
out
the
Wipe gently with clean cloth and neutral
glass detergent or weak alkaline glass
detergent.
After that, clean surface of glass with wet
and clean cloth.
Acid and strong alkaline detergent and the
continuous
detergent which forms protective layer on
the surface of the glass must be avoided.
Those detergents may damage surface of
the glass and affect on the performance
of solar panel. Please be very careful
since warranty will not cover the damage
from detergent.
When
cleaning
recommended to start with smallest area
and from the edge of solar panel in
order to check no damage occurs to the
glass.
It is recommended to read carefully the
manuals
of
notes on usage and first-aid treatment.
strong
acid
Disclaimer of Liability
Panasonic does not assume responsibility and
may
be
expressly disclaims liability for loss, damage, or
expense
arising
connected with installation, operation, use, or
maintenance by using this manual.
it
is
Panasonic assumes no responsibility for any
infringement of patents or other rights of third
parties, which may result from use of modules.
No license is granted by implication or under
any patent or patent rights. The information in
22 cells / diode
22 cells / diode
22 cells / diode
22 cells / diode
detergent
and
understand
persistent
dirt,
soiling
of
solar
panel.
In
case
customer
prefers
with
detergent,
it
detergent
and
understand
out
of,
or
in
any
way
of
is