Panasonic RX-D19 Operating Instructions Manual - Page 3
Browse online or download pdf Operating Instructions Manual for Stereo System Panasonic RX-D19. Panasonic RX-D19 9 pages. Portable stereo cd system
Print Page
Normal tuning
3 2 1
1
Switch [
] to "TUNER".
(Unit comes on.)
2
Press [BAND] to select "FM" or "AM".
3
(Omit this step if using the remote control)
If "
" is on the display, press
[TUNE MODE] to clear it off.
4
Press [–/g] or [f/+] to
tune to the desired station.
The frequency changes one step
each time a button is pressed.
Automatic tuning
Keep [–/ g] or [f/+] depressed and release when the frequency
display starts to change. A station with good reception is automati-
cally selected and the process stops.
To stop automatic tuning, press [–/ g] or [f/+] again.
Note
Automatic tuning may stop on a frequency where there is no station if
there is interference. Press [–/ g] and [f/+] to tune if this occurs.
5
Adjust the volume.
To use auto scan
You can search for a station by listening to all tuned-in stations for 8
seconds each.
Preparation: Switch [
1. Press [BAND] to select "FM" or "AM".
2. Press [AUTO SCAN].
Auto scan starts.
Indicates
auto scan
3. Press [AUTO SCAN] when you find the desired station.
Auto scan ends when it reaches the original frequency again.
To stop during the process, press [AUTO SCAN].
To improve reception
FM: Extend the whip antenna and adjust its direction.
AM: Adjust facing of the unit.
If noise is excessive in the FM stereo mode
Press [FM MODE]. ("
" lights up.)
Sound will be produced in monaural, but this also reduces noise.
Press the button again to cancel. ("
P3-4
The Radio
5
4
"
" lights when an FM stereo
broadcast is being received.
] to "TUNER".
" goes out.)
3
Preset tuning
Preset the stations (twelve FM and twelve AM) to make tuning simpler.
1 2 4
How to preset
Preparation: Tune to the desired station.
(Do steps 1–4 on the left.)
1
Press [MEMORY].
2
While "
" and the frequency are
flashing
Press [MEMORY].
3
While "
" and the preset channel
are flashing
Press [–/g] or [f/+] to
select the desired channel.
(Remote control: [4 4 4 4 4 ] or [3 3 3 3 3 ])
4
Press [MEMORY].
(This completes presetting.)
Repeat the above to preset other stations.
Note
If "
" goes off during presetting, return to step 1.
To listen to preset channels
1 1 1 1 1
Press [BAND] to select "FM" or "AM".
2
(Omit this step if using the remote control)
Press [TUNE MODE] to display
"
".
3
Press [–/ g] or [f/+] to select
the desired channel (1–12).
(Remote control: [4 4 4 4 4 ] or [3 3 3 3 3 ])
To use preset scan
You can search for a station by listening to all preset channels for 8
1
2
seconds each.
1. Do steps
to
above.
For remote control, replace [– / g] or [f/+] described below with [4 4 4 4 4 ]
or [3 3 3 3 3 ].
2. Press and hold [–/ g] or [f/+] until "PS" appears on the display.
Indicates
preset scan
3. Press [–/ g] or [f/+] when you find the desired channel.
Preset scan ends after searching through each preset channel once.
To stop during the process, press [–/ g] or [f/+].
3
RQT6341
11/21/01, 7:05 PM
3
2
3
1
Preset channel
Preset channel