Panasonic RX-D50 Operating Instructions Manual - Page 6

Browse online or download pdf Operating Instructions Manual for Stereo System Panasonic RX-D50. Panasonic RX-D50 14 pages. Portable stereo cd system
Also for Panasonic RX-D50: Operating Instructions Manual (12 pages), Operating Instructions Manual (24 pages), Operating Instructions Manual (28 pages)

Print Page

Panasonic RX-D50 Operating Instructions Manual

Cassette tape – Play and record

Basic play

Use normal position tapes.

High position and metal position tapes can be played, but the unit will not be

able to identify the characteristics of these tapes.

Press [TAPE/OFF].

Open the cassette operation buttons' lid.

Press [8/x, STOP/EJECT] and insert the cassette.

Insert with the side to be played facing up and the exposed tape facing

towards you. Close the deck by hand.

Press [4, PLAY] to start play.

Stop tape

Press [8/x, STOP/EJECT].

playback

Pause play

Press [9, PAUSE].

Press again to resume play.

Fast-forward

Press [3, REW/REV] or [5, FF/CUE] in the stop

and rewind

mode.

Search for a

Press [3, REW/REV] (to search backward) or

speciﬁ c point

[5, FF/CUE] (to search forward) during playback.

Play is resumed when the button is released.

Recording

Use normal position tapes.

High position and metal position tapes can be used, but the unit will not be able

to record or erase them correctly.

✒

Preparation

Wind up the source tape so recording can begin immediately.

Press [0, STOP/EJECT] and insert the cassette to be recorded.

Insert with the side to be recorded facing up and the exposed tape facing

towards you.

Select the source to be recorded.

Prepare the USB mass storage device for recording

RX-D55

(Z page 6).

USB

Radio

Tune in the station (Z page 6).

Disc

1. Insert the disc you want to record.

Press [4/9, CD] and then [8] (stop).

2. Prepare the desired disc recording mode.

Record programmed tracks

Program the tracks you want (Z page 5).

Record speciﬁ c albums or tracks

Press [PLAY MODE] to select the desired mode

(Z page 5).

Music port

Select music port (Z page 8).

Press [ V

] to start recording.

Stop recording

Press [8/x, STOP/EJECT].

Turn the cassette over and press [ V

Record on the other

side of the tape

Erase a recorded

1. Press [TAPE/OFF].

sound

2. Insert the recorded cassette.

3. Press [ V

✒

Note

Changes to volume and sound quality do not affect recording.

Erasure prevention

The illustration shows how to remove the tabs to prevent recording. To record on

the tape again, cover as shown.

To prevent recording

Side A

Tab for Side B

Tab for Side A

✒

Note

• Tapes exceeding 100 minutes are thin and can break or get caught in the

mechanism.

• Tape slack can get caught up in the mechanism and should be wound up

before the tape is played.

• Endless tapes can get caught up in the deck's moving parts if used incorrectly.

To re-record

Adhesive tape

Using the clock and timers

Setting the clock

This is a 24-hour clock.

Press [CLOCK/TIMER].

Each time you press the button:

CLOCK

Original display

Within 5 seconds or so

Press [2/3] or [5/6] to set the time.

Holding down the button will speed up the time selection.

Press [CLOCK/TIMER] to ﬁ nish setting the time.

Displaying the clock

Press [CLOCK/TIMER] to display the clock for few seconds.

✒

Note

• Reset the clock regularly to maintain accuracy.

• When the unit is in standby mode and it is powered by batteries, clock will not

be displayed.

Using the play timer

You can set the timer to come on at a certain time to wake you up.

✒

Preparation

• Turn the unit on and set the clock.

• Prepare the music source you want to listen to; disc, radio, USB (

or music port source, and set the volume.

Press [CLOCK/TIMER] repeatedly to select the play timer.

Within 5 seconds or so

Press [2/3] or [5/6] to set the

starting time.

Press [CLOCK/TIMER] to conﬁ rm.

Repeat steps 2 and 3 to set the ﬁ nishing

time.

To activate the timer

Press [# PLAY] to turn on the timer.

# PLAY

Press [TAPE/OFF] to turn off the unit.

Change the

Repeat steps 1 to 4 and 6 (Z see above).

settings

Change the source

1. Press [# PLAY] to clear the timer indicator from the

or volume

display.

2. Make changes to the source or volume.

3. Perform steps 5 and 6 (Z see above).

Press [CLOCK/TIMER] repeatedly to select # PLAY

Check the settings

(when the unit is on

(there is no display when the unit is powered by

or in standby mode)

batteries and is in standby mode).

Cancel

Press [# PLAY] to clear the timer indicator from the

display.

✒

Note

• The play timer will start at the preset time, with the volume increasing

gradually to the preset level.

• The timer comes on at the set time every day if the timer is on.

• The unit must be in the standby mode for the timer to function.

• If you turn the unit off and on again while a timer is functioning, the ﬁ nish time

setting will not be activated.

Using the sleep timer

This function enables you to turn off the unit automatically after the set time

except in tape mode.

Press [SLEEP] repeatedly to select your desired time (in minutes).

To cancel

Press [SLEEP] repeatedly to select "OFF".

Changing the remaining time

Press [SLEEP] to show the remaining time, and press [SLEEP] again to select

your desired time.

✒

Note

• The play and sleep timer can be used together.

• The sleep timer always has priority. Be sure not to overlap timer settings.

# PLAY ON

RX-D55

No display (off)

only)